Qtech QSW-8200-52T-AC — user Manual for EFM OAM Commands and Link Event Management [61/85]
Превью страниц
Страница 61 /
85
![Qtech QSW-8200-28T-AC-DC [61/85] Show ethernet oam events](/views2/1596641/page61/bg3d.png)
User Manual
Chapter 8. Commands for EFM OAM 61
www.qtech.ru
local_mux_action
Working mode of the local transmitter:
FWD, the port can send any packets;
DISCARD, the port only sends OAMPDU packets and
discards others.
local_par_action
Working mode of the local receiver in the following:
FWD, receiving any packets is allowed;
DISCARD, only OAMPDU packets is received while others
are discarded;
LB, OAM remote loopback is enabled on the port. In this
case, all the packets except OAMPDU packets received
are returned to their sources along the ways they come.
Loopback Supported
Whether support remote loopback: YES for support and
NO for not.
Unidirectional Support
Whether support unidirectional transmission: YES for
support and NO for not.
Link Events
Whether support general link events: YES for support and
NO for not.
Remote Failure
Whether support severe link events: YES for support and
NO for not.
Max_OAMPDU_Size
The maximum length of OAMPDU is supported.
Link Fault
Whether occur a Link Fault event: 0 for no and 1 for yes.
Dying Gasp
Whether occur a Dying Gasp event: 0 for no and 1 for yes.
Critical Event
Whether occur a Critical Event: 0 for no and 1 for yes.
8.27 show ethernet-oam events
Command: show ethernet-oam events {local | remote} [interface {ethernet |}
<IFNAME>]
Function: Shows the statistic information of link events on specified or all ports with
OAM enabled, including general link events and severe link events.
Содержание
- Chapter 1 commands for network port configuration 7 p.2
- Show isolate port group 21 p.2
- Chapter 2 commands for port isolation function 20 p.2
- Loopback detection specified vlan 25 p.2
- Loopback detection interval time 24 p.2
- Loopback detection control recovery timeout 24 p.2
- Loopback detection control 23 p.2
- Isolate port group switchport interface 20 p.2
- Isolate port group 20 p.2
- Isolate port apply 21 p.2
- Debug loopback detection 23 p.2
- Content p.2
- Commands for ethernet port configuration 7 p.2
- Chapter 3 commands for port loopback detection function 23 p.2
- Show loopback detection 25 p.2
- Configuration p.7
- Commands for ethernet port configuration p.7
- Chapter 1 commands for network port p.7
- Isolate port group switchport interface p.20
- Isolate port group p.20
- Chapter 2 commands for port isolation function p.20
- Show isolate port group p.21
- Isolate port apply p.21
- Loopback detection control p.23
- Function p.23
- Debug loopback detection p.23
- Chapter 3 commands for port loopback detection p.23
- Loopback detection interval time p.24
- Loopback detection control recovery timeout p.24
- Show loopback detection p.25
- Loopback detection specified vlan p.25
- Debug uldp event p.26
- Debug uldp error p.26
- Debug uldp p.26
- Chapter 4 commands for uldp p.26
- Debug uldp packet p.27
- Debug uldp interface ethernet p.27
- Debug uldp fsm interface ethernet p.27
- Uldp enable p.28
- Uldp aggressive mode p.28
- Uldp manual shutdown p.29
- Uldp hello interval p.29
- Uldp disable p.29
- Uldp reset p.30
- Uldp recovery time p.30
- Show uldp p.30
- Debug lldp packets p.32
- Debug lldp p.32
- Clear lldp remote table p.32
- Chapter 5 commands for lldp function p.32
- Lldp mode p.33
- Lldp enable port p.33
- Lldp enable p.33
- Lldp notification interval p.34
- Lldp neighbors max num p.34
- Lldp msgtxhold p.34
- Lldp transmit optional tlv p.35
- Lldp transmit delay p.35
- Lldp toomanyneighbors p.35
- Lldp tx interval p.36
- Lldp trap p.36
- Show debugging lldp p.37
- Show lldp p.37
- Show lldp neighbors interface ethernet p.38
- Show lldp interface ethernet p.38
- Show lldp traffic p.39
- Interface port channel p.40
- Debug port channel p.40
- Chapter 6 commands for port channel p.40
- Lacp timeout p.41
- Lacp system priority p.41
- Lacp port priority p.41
- Port group mode p.42
- Port group p.42
- Load balance p.42
- Show port group p.43
- Chapter 7 commands for mtu p.45
- Chapter 8 commands for efm oam p.46
- Debug ethernet oam fsm p.46
- Debug ethernet oam error p.46
- Clear ethernet oam p.46
- Ethernet oam p.47
- Debug ethernet oam timer p.47
- Debug ethernet oam packet p.47
- Ethernet oam errored frame threshold low p.48
- Ethernet oam errored frame threshold high p.48
- Ethernet oam errored frame window p.49
- Ethernet oam errored frame period threshold low p.49
- Ethernet oam errored frame period threshold high p.49
- Ethernet oam errored frame seconds threshold high p.50
- Ethernet oam errored frame period window p.50
- Ethernet oam errored frame seconds window p.51
- Ethernet oam errored frame seconds threshold low p.51
- Ethernet oam errored symbol period threshold high p.52
- Ethernet oam errored symbol period threshold low p.52
- Ethernet oam link monitor p.53
- Ethernet oam errored symbol period window p.53
- Ethernet oam remote failure p.54
- Ethernet oam period p.54
- Ethernet oam mode p.54
- Ethernet oam remote loopback supported p.55
- Ethernet oam remote loopback p.55
- Show ethernet oam p.56
- Ethernet oam timeout p.56
- Show ethernet oam events p.61
- Show ethernet oam link events configuration p.64
- Show ethernet oam loopback status p.65
- Bpdu tunnel stp p.67
- Bpdu tunnel gvrp p.67
- Bpdu tunnel dmac p.67
- Chapter 9 commands for bpdu tunnel p.67
- Bpdu tunnel uldp p.68
- Bpdu tunnel lacp p.68
- Bpdu tunnel dot1x p.68
- Description language province state city county street locationnum location floor room postal otherinfo p.70
- Civic location p.70
- Chapter 10 commands for lldp med p.70
- Lldp med fast count p.71
- Ecs location p.71
- Lldp transmit med tlv capability p.72
- Lldp transmit med tlv all p.72
- Lldp med trap p.72
- Lldp transmit med tlv inventory p.73
- Lldp transmit med tlv extendpoe p.73
- Network policy p.74
- Lldp transmit med tlv networkpolicy p.74
- Show lldp p.75
- Show lldp neighbors p.77
- Clear port security p.78
- Switchport port security p.78
- Show port security p.78
- Chapter 11 commands for port security p.78
- Switchport port security mac address p.79
- Switchport port security aging p.79
- Switchport port security maximum p.80
- Switchport port security mac address sticky p.80
- Switchport port security violation p.81
- Show transceiver p.82
- Debug transceiver p.82
- Clear transceiver threshold violation p.82
- Chapter 12 commands for ddm p.82
- Show transceiver threshold violation p.83
- Transceiver monitoring p.83
- Transceiver threshold p.84
- Transceiver monitoring interval p.84
Похожие устройства
-
Qtech QSW-1500-20EF-POE-ACТехнические характеристики -
Qtech QSW-1500-19EF-POE-AC V3Описание параметров -
Qtech QSW-1500-10E-POE-DОписание параметров -
Qtech QSW-1500-6E-POE-DПодробное техническое описание -
Qtech QSW-4610Инструкция пользователя -
Qtech QSW-3750 REV. RИнструкция пользователя -
Qtech QSW-3750Руководство по эксплуатации -
Qtech QSW-3420Инструкция по применению -
Qtech QSW-9000-01Руководство по управлению -
Qtech QSW-9000-01Руководство по настройке -
Qtech QSW-9000-01Руководство по настройке управления -
Qtech QSW-9000-01Руководство по командам
Explore the user manual detailing commands for EFM OAM, including local transmitter modes, loopback support, and link event statistics for efficient network management.