Moser Genio [12/120] English

Moser Genio [12/120] English
ENGLISH
de
en
fr
it
es
pt
nl
sv
no
fi
tr
pl
cs
sk
hu
sl
ro
bg
ru
uk
el
ar
12
Operation
Preparation
Keep the packaging material for later safe storage or
transport.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Handle with care! Damage due to incorrect power
supply.
f Only operate the appliance with an alternating cur-
rent and with the voltage stated on the nameplate.
Charging the battery
Before the appliance is used for the first time, it
should be charged for approx.
16 hours!
1. Connect the appliance plug (J) on the plug-in transformer to
the appliance socket (D) (Fig. 2).
2. Insert the plug-in transformer into the mains socket.
3. Switch off the appliance using the on/off switch (Fig. 3
).
· During charging, the charging indicator light (C)
is illuminated.
· It should take around
10 hours for the appliance
to charge to full capacity.
Battery operation
1. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3
/
).
· When the battery is fully charged, the appliance
can be used for up to
100 minutes without mains
connection. This capacity is attained after approx.
5 - 10 charging cycles.
· In case of insufficient maintenance of the
blade set, the operating time can be reduced
considerably.
Mains operation
1. Connect the appliance plug (J) on the plug-in transformer to
the appliance socket (D) (Fig. 2).
2. Insert the plug-in transformer into the mains socket.
3. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3
/
).
Operation
Cutting with the attachment combs
The appliance can also be operated with attachment combs.
The following attachment combs are included as standard:
· Attachment comb small = cutting lengths 3 mm and 6 mm
· Attachment comb large = cutting lengths 9 mm and 12 mm
· The cutting length (in mm) is shown on the attach-
ment comb.
· One attachment comb can be used for two differ-
ent cutting lengths. For the second cutting length,
all you need to do is remove the attachment
comb, rotate and replace.
· The advantage of these attachment combs is that
no matter the angle at which you approach the
hair, you always achieve the same cutting length.
Attaching/removing the attachment comb
1. Place the attachment comb onto the cutting edge of the
blade set and press it down onto the blade set into the
knobs in the direction of the housing until it clicks into posi-
tion (Fig. 4
).
2. The attachment comb can be removed by pushing it in
towards the cutting edge (Fig. 4
).
Maintenance
Cleaning and care
Danger! Electric shock due to penetration of
liquid.
f Switch the appliance off and disconnect it from
the power supply, before you start with cleaning
and care.
f Do not immerse the appliance into water!
f Do not allow any liquid to get inside the appliance.
f Only reconnect the appliance to the power supply
if it is completely dry.
Handle with care! Damages due to aggressive
chemicals.
Aggressive chemicals could damage the appliance
and accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
Hygienic spray and blade set oil are available from
your dealer or our service centre.
f After every use, remove the attachment comb (Fig. 4
)
and lift the blade set out of the housing (Fig. 5
). Use the
cleaning brush to remove any cut hairs from the housing
opening and from the blade set (Fig. 6). The cleaning lever
can also be pressed. This allows the cut hairs that accumu-
late between the bottom blade and the top blade to be eas-
ily removed using the cleaning brush (
EASY CLEANING).
f Always keep the appliance socket (D) clean.
f Only wipe the appliance with a soft cloth, possibly slightly
damp.
f Clean the blade set using the hygienic spray.
f Oil the blade set with the blade set oil (Fig. 7).

Содержание