Indesit W 431 TX [23/52] Before calling read the following

Indesit W 431 TX [23/52] Before calling read the following
The washing machine
fails to fill with water.
Is the hose correctly
connected to the tap?
Is there a water shortage ?
There could be work in
progress in your building or
street.
Is there sufficient water
pressure? The autoclave
may be malfunctioning.
Is the tap filter clean? If the
water is very calcareous, or
if work has recently been
carried out on the water
piping, the tap filter could be
clogged with particles and
debris.
Is the rubber hose kinked?
The tract of the rubber hose
bringing water to washing
machine must be as straight
as possible. Make sure it is
not squashed or kinked.
The washing machine
continuously fills and
drains water.
Is the drain hose positioned
too low? It must be installed
at a height ranging from 60 to
100 cm.
Is the end of the hose
immersed in water?
Does the wall drainage
system have a breather
pipe? If the problem persists
even after these checks, turn
the water supply off the
machine and call for
assistance.
If you live on an upper floor of
your building, there may be a
problem with your drain trap.
To solve this problem, a
special valve must be
installed.
Before calling, read the following
Troubleshooting
In most cases, when your washing machine fails to work, the problems arising
can be easily solved without having to call for a technician. Before calling for
assistance, always check these points.
The washing machine
fails to start.
Is the plug correctly inserted
into the socket? It could have
been moved whilst cleaning.
Is there electricity in the
house?
A circuit breaker may have
switched off as a result of too
many electrical appliances
working at the same time. Or
maybe due to a general failure
in your entire area.
Is the washing machine
door closed properly?
For safety reasons, the
washing machine cannot work
if the door is open or not shut
properly.
Is the On/Off button
pressed?
If it is, then a programmed start
has been set.
Is the programmed start
knob, in the correct position
for those models
concerned?
Is the water supply turned
on? For safety reasons, if the
washing machine does not
load water, it cannot start a
wash cycle.
RIGHT WRONG
Turn off the water
supply after use.
This will eliminate
the possibility of
leakage.
Always leave the
appliance door ajar
to avoid bad odours.
Clean the
appliance’s
exteriors gently.
To clean the
exteriors and the
rubber parts of the
appliance, always
use a soft cloth
dipped in warm and
soapy water.
Leave the washing
machine plugged in while
cleaning.
Even during maintenance,
the appliance should
always be unplugged.
Use solvents and
aggressive abrasives.
Never use solvents or
abrasives to clean the
external and rubber parts
of the washing machine.
Neglect the detergent
dispenser.
It is removable and can
easily be cleaned by
leaving it under running
water.
Go on holiday without
thinking about her.
Before leaving, always
make sure that the
washing machine is
unplugged and that the
water supply is turned off.
Instructions for installation and us
e
20

Содержание

Troubleshooting Before calling read the following In most cases when your washing machine fails to work the problems arising can be easily solved without having to call for a technician Before calling for assistance always check these points The washing machine fails to start Is the plug correctly inserted into the socket It could have been moved whilst cleaning Is there electricity in the house A circuit breaker may have switched off as a result of too many electrical appliances working at the same time Or maybe due to a general failure in your entire area Is the washing machine door closed properly if the door is open or not shut properly Is the pressed On Off button If it is then a programmed start has been set Is the programmed start knob in the correct position for those models concerned Is the water supply turned on For safety reasons if the washing machine does not load water it cannot start a wash cycle For safety reasons the washing machine cannot work RIGHT WRONG Turn off the water supply after use This will eliminate the possibility of leakage Always leave the appliance door ajar to avoid bad odours Clean the appliance s exteriors gently To clean the exteriors and the rubber parts of the appliance always use a soft cloth dipped in warm and soapy water Leave the washing machine plugged in while cleaning Even during maintenance the appliance should always be unplugged Use solvents and aggressive abrasives Never use solvents or abrasives to clean the external and rubber parts of the washing machine Neglect the detergent dispenser It is removable and can easily be cleaned by leaving it under running water Go on holiday without thinking about her Before leaving always make sure that the washing machine is unplugged and that the water supply is turned off The washing machine continuously fills and drains water The washing machine fails to fill with water Is the hose correctly connected to the tap Is the drain hose positioned too low It must be installed Is there a water shortage in or at a height ranging from 60 to 100 cm water Is the end of the hose immersed in water There could be work progress in your building street Is there pressure sufficient The autoclave may be malfunctioning Is the tap filter clean If the water is very calcareous or if work has recently been carried out on the water piping the tap filter could be clogged with particles and debris Is the rubber hose kinked The tract of the rubber hose bringing water to washing machine must be as straight as possible Make sure it is not squashed or kinked Does the wall drainage system have a breather pipe If the problem persists even after these checks turn the water supply off the machine and call for assistance If you live on an upper floor of your building there may be a problem with your drain trap To solve this problem a special valve must be installed Instructions for installation and use 20