Black & Decker LD12SP [10/61] English

Black & Decker LD12SP [10/61] English
10
ENGLISH
(Original instructions)
Drilling in wood
Holes in wood can be made with the same
twist drill bits used for metal or with spade
bits. These bits should be sharp and should
be pulled out frequently when drilling to
clear chips from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals.
The exceptions are cast iron and brass
which should be drilled dry. The cutting
lubricants that work best are sulfurized
cutting oil or lard oil.
Cell indicator
When press the main trigger (1), the cell
capacity indicator turn on at the same to
show the cell capacity status.
Troubleshooting
Maintenance
Your BLACK+DECKER tool has been
designed to operate over a long period of
time with a minimum of maintenance.
Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Your charger does not require any
maintenance apart from regular cleaning.
Warning! Before performing any
maintenance on the tool, remove the
battery from the tool. Unplug the
charger before cleaning it.
Regularly clean the ventilation slots in
your tool and charger using a soft brush
or dry cloth.
Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner.
Regularly open the chuck and tap it to
remove any dust from the interior.
Important! To ensure product SAFETY and
RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this
manual) should be performed by authorized
service centers or other qualified
organizations, always using identical
replacement parts. Unit contains no user
service able parts inside.
Accessories
Recommended accessories for use with your
tool are available at extra cost from your
local dealer or authorized service center.
100 %
0 %
Problem Possible cause Possible solution
Unit will not
start.
Battery pack
will not charge.
Battery pack not
inserted into charger.
Charger not plugged
in.
Battery pack not
installed properl
Battery pack not
charged.
Check battery pack
installation.
Insert battery pack
into charger until green
LED appears
Plug charger into
aworking outlet. Refer
to “Important Charging
Notes” formore details.
Check battery pack
charging requirements.
Battery pack has
reached its
maximumthermal
limit.
Out of charge.
(To maximize the life
of the battery pack
it is designed to
shut o abruptly
when the charge is
depleted.)
Unit shuts o
abruptly.
Surrounding air
temperature too hot
or too cold.
Move charger and
battery pack to a
surrounding air
temperature of above
40 oF 4,5°C) or below
105 oF (+40,5°C).
Allow battery pack to
cool down.
Place on charger and
allow to charge.

Содержание

ENGLISH Original instructions Drilling in wood Holes in wood can be made with the same twist drill bits used for metal or with spade bits These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes Unit shuts off abruptly Surrounding air temperature too hot or too cold Move charger and battery pack to a surrounding air temperature of above 40 oF 4 5 C or below 105 oF 40 5 C Battery pack has reached its maximumthermal limit Allow battery pack to cool down Out of charge To maximize the life of the battery pack it is designed to shut off abruptly when the charge is depleted Place on chargerand allow to charge Drilling in metal Use a cutting lubricant when drilling metals The exceptions are cast iron and brass which should be drilled dry The cutting lubricants that work best are sulfurized cutting oil or lard oil Cell indicator When press the main trigger 1 the cell capacity indicator turn on at the same to show the cell capacity status Maintenance Your BLACK DECKER tool has been designed to operate over a long period of time with a minimum of maintenance Continuous satisfactory operation depends upon proper tool care and regular cleaning Your charger does not require any maintenance apart from regular cleaning Warning Before performing any J maintenance on the tool remove the battery from the tool Unplug the charger before cleaning it I g aj V Regularly clean the ventilation slots in your tool and charger using a soft brush or dry cloth 0 Troubleshooting Problem Unit will not start Battery pack will not charge Possible cause Possible solution Regularly clean the motor housing using a damp cloth Do not use any abrasive or solvent based cleaner Battery pack not installed properl Check battery pack installation Regularly open the chuck and tap it to remove any dust from the interior Battery pack not charged Check battery pack charging requirements Battery pack not inserted into charger Insert battery pack into charger until green LED appears Charger not plugged in Plug charger into aworking outlet Refer to Important Charging Notes formore details Important To ensure product SAFETY and RELIABILITY repairs maintenance and adjustment other than those listed in this manual should be performed by authorized service centers or other qualified organizations always using identical replacement parts Unit contains no user service able parts inside Accessories Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center 10

Скачать