Bosch GWX 9-125 S (06017B2000) X-lock [21/288] Operation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bosch GWX 9-125 S (06017B2000) X-lock [21/288] Operation

Bosch GWX 9-125 S (06017B2000) X-lock [21/288] Operation
English | 21
Bosch Power Tools 1 609 92A 3EC | (17.2.17)
The machine head can be
rotated with respect to
the machine housing in
90° steps. In this man-
ner, the On/Off switch
can be brought into a
more convenient posi-
tion for special working
situations, e.g. for left-
handed persons.
Completely unscrew the
four screws. Rotate the
machine head carefully,
without removing it from the housing, to the new position.
Screw in and tighten the four screws again.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Hold power tool by insulated gripping surfaces 21 and
auxiliary handle 4 only. The accessory may contact hid-
den wiring or its own cord. Accessory contacting a “live”
wire may make exposed metal parts of the power tool “live”
and shock the operator.
When operating the machine with power from mobile genera-
tors that do not have sufficient reserve capacity or are not
equipped with suitable voltage control with starting current
amplification, loss of performance or untypical behavior can
occur upon switching on.
Please observe the suitability of the power generator being
used, particularly with regard to the mains voltage and fre-
quency.
Switching On and Off
To start the power tool, push the On/Off switch 2 forwards.
To lock the On/Off switch 2, press the On/Off switch 2 down
at the front until it latches.
To switch off the power tool, release the On/Off switch 2 or,
if it is locked, briefly push down the back of the On/Off switch
2 and then release it.
Check grinding tools before using. The grinding tool
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grind-
ing tools. Damaged grinding tools can burst and cause in-
juries.
To save energy, only switch the power tool on when using it.
Restarting Protection (GWS 9-115 S/GWS 9-125S)
The restarting protection feature prevents uncontrolled re-
starting of the machine after an interruption in the power sup-
ply.
To restart the operation, switch the On/Off switch 2 to the
Off position and start the machine again.
Speed preselection (GWS 9-115 S/GWS 9-125S)
The required speed can be preselected with the thumbwheel 3 (also while running).
The data in the following table are recommended values.
Material Application Accessory Thumbwheel Position
Metal Removing paint Sanding disc 2 – 3
Metal Brushing, rust removal Cup brush, sanding disc 3
Metal, masonry Grinding Grinding disc 4 – 6
Metal Rough grinding Grinding disc 6
Metal Cutting Cutting disc 6
OBJ_BUCH-3020-001.book Page 21 Friday, February 17, 2017 9:19 AM

Содержание

Похожие устройства

Скачать