Bosch GSR 12 V-EC TE (06019E4002) — инструкция по эксплуатации аккумуляторного инструмента [14/163]
Макгруп McGrp.ru

Bosch GSR 12 V-EC TE (06019E4002) — инструкция по эксплуатации аккумуляторного инструмента [14/163]

Превью страниц Страница 14 / 163
Bosch GSR 12 V-EC TE (06019E4002) [14/163] Operation
14 | English
2 609 141 186 | (9.12.14) Bosch Power Tools
Operation
Starting Operation
Inserting the battery
Use only original Bosch lithium-ion batteries with the
voltage listed on the nameplate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Set the rotational direction switch 5 to the centre position in
order to avoid unintentional starting. Insert the charged bat-
tery 7 into the handle so that it can be felt to engage and faces
flush against the handle.
Reversing the rotational direction
The rotational direction switch 5 is used to reverse the rota-
tional direction of the machine. However, this is not possible
with the On/Off switch 10 actuated.
Rotate clockwise: Move the rotational direction switch 5
on both sides up to the stop into position .
Rotate anticlockwise: Move the rotational direction
switch 5 on both sides up to the stop into position .
Switching On and Off
To start the machine, press the On/Off switch 10 and keep it
pressed.
The LED 12 lights up when the On/Off switch 10 is halfway or
fully pressed, and enables illumination of the screwing loca-
tion in unfavourable light conditions.
To switch off the machine, release the On/Off switch 10.
To save energy, only switch the power tool on when using it.
Adjusting the Speed
The speed of the switched-on power tool can be variably ad-
justed, depending on how far the On/Off switch 10 is
pressed.
Light pressure on the On/Off switch 10 results in a low rota-
tional speed. Further pressure on the switch results in an in-
crease in speed.
Adjusting the Screw-in Depth (see figure B)
With the adjustment sleeve 3, the screw-in depth of the screw
head into the workpiece can be preset in 8 locking steps per
full turn. Each step corresponds with a 0.25 mm change of
the screw-in depth.
Turning the adjustment sleeve 3 in clockwise direction results
in a greater screw-in depth; turning in anticlockwise direction
reduces the screw-in depth.
The required setting is best determined by testing.
Temperature Dependent Overload Protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the power output is re-
duced or the power tool is switched off. The power tool will
not run at full power output again until the permitted battery
temperature has been reached.
Protection Against Deep Discharging
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Working Advice
Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
Guide the screw toward the screwdriving bit 1. The screw is
held in place by the magnet pull of the universal bit holder 11.
Firmly push the tip of the screw into the material to be
screwed until the screwing-depth stop 4 faces against the
workpiece.
Switch the machine on. The screw is screwed into the materi-
al until the adjusted screw-in depth is reached. The drive is
disengaged and the tool holder no longer rotates. Check the
screw-in depth and readjust, if required.
For unscrewing screws, set the rotational direction switch 5
to left rotation and pull off the screwing-depth stop 4 toward
the front without turning the adjustment sleeve.
Working with the screwing-depth stop 4 is also possible when
adapting the screw-in depth.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
To ensure trouble-free operation of the power tool, clean the
mount of the universal bit holder 11 and the screwing-depth
stop 4 with compressed air at regular intervals.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
OBJ_BUCH-2205-001.book Page 14 Tuesday, December 9, 2014 12:02 PM

Содержание

700

Похожие устройства

Узнайте, как правильно использовать аккумуляторный инструмент: вставка батареи, регулировка скорости и защита от перегрева. Безопасность и эффективность в работе.