Home
Главная
STATUS
УШМ (болгарка)
SA230SF
Инструкция по эксплуатации Страница: 3

STATUS SA230SF [3/30] General power tool safety warnings

1.GENERAL POWER TOOL SAFETY WARNINGS

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional staring. Ensure the switch is in the off-position

before connecting to power source and /or battery pack, picking up or

carrying the tool. Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result

in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the rate

for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous and

must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from

the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of

staring the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate

the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the

power tool's operationIf damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with

these instructions. Use of the power tool for operations different from

those intended could result in a hazardous situation.

2. SAFETY INSTRUCTIONS FOR ANGLE GRINDERS

SAFETY INSTRUCTIONS FOR ANGLE GRINDERS

1) SAFETY INSTRUCTIONS FOR ALL OPERATIONS

a) This power tool is intended to function as a grinder, sander, wire

brush, polisher or cut-off tool. Read all safety warnings,

instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in

electric shock, fire and/or serious injury.

b) Operations such as grinding, sanding, wire brushing, polishing or

cutting-off are not recommended to be performed with this power

tool. Operations for which the power tool was not designed may create

a hazard and cause personal injury.

NOTE: List only those operations that were not included in the first warning.

If all listed operations are recommended, then this warning may be omitted

but all subsequent warnings must be given without an exclusion.

c) Do not use accessories which are not specifically designed and

recommended by the tool manufacturer. Just because the accessory

can be attached to your power tool, it does not assure safe operation.

d) The rated speed of the accessory must be at least equal to the

maximum speed marked on the power tool. Accessories running

faster than their rated speed can break and fly apart.

e) The outside diameter and the thickness of your accessory must

be within the capacity rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or controlled.

f) The arbour size of wheels, flanges , backing pads or any other

accessory must properly fit the spindle of the power tool.

Accessories with arbour holes that do not match the mounting hardware

of the power tool will run out of balance, vibrate excessively and may

cause loss of control.

g) Do not use a damaged accessory. Before each use inspect the

accessory such as abrasive wheels for chips and chips and cracks ,

backing pad for cracks, tear or excess wear, wire brush for chips

and cracks, backing pad for cracks, tear or excess wear, wire brush

for loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory and run

the power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during this test time.

h) Wear personal protective equipment. Depending on application,

use face shield, safety goggles or safety glasses. As appropriate,

wear dust mask, hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece fragments.

STATUS SA230SF [3/30] General power tool safety warnings

Содержание

Похожие устройства