Black & Decker ASD18KB [8/76] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Black & Decker ASD18KB [8/76] English

Black & Decker ASD18KB [8/76] English
ENGLISH
8
(Original instructions)
• Insert the bit shaft into the chuck and
firmly tighten the single sleeve chuck.
This tool is supplied with a screwdriver bit in
the bit holder (7).
• To remove the screwdriver bit from the
bit holder, lift the bit from the recess.
• To store the screwdriver bit, firmly push
it into the holder.
Warning! Do not attempt to tighten drill bits
(or any other accessory) by gripping the
single sleeve chuck and turning the tool on.
Damage to the single sleeve chuck and
personal injury may occur when changing
accessories.
Use
Warning! Let the tool work at its own pace.
Do not overload.
Warning! Before drilling into walls, floors or
ceilings, check for the location of wiring and
pipes.
Charging the battery (fig. A)
The battery needs to be charged before first
use and whenever it fails to produce
sufficient power on jobs that were easily
done before. The battery may become
warm while charging; this is normal and
does not indicate a problem.
Warning! Do not charge the battery at
ambient temperatures below 10 °C or above
40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery
if the cell temperature is below
approximately 10°C or above 40°C. The
battery should be left in the charger and
the charger will begin to charge
automatically when the cell temperature
warms up or cools down.
• To charge the battery (8), insert it into
the charger (9). The battery will only fit
into the charger in one way. Do not force.
Be sure that the battery is fully seated in
the charger.
• Plug in the charger and switch on at the
mains.
The charging indicator (10) will blink.
The charge is complete when the charging
indicator (10) switches to continuously on.
The charger and the battery can be left
connected indefinitely. The LED will switch
on as the charger occasionally tops up the
battery charge.
• Charge discharged batteries within 1
week. Battery life will be greatly
diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left
connected with the LED glowing indefinitely.
The charger will keep the battery pack fresh
and fully charged.
Charger diagnostics
If the charger detects a weak or damaged
battery, the charging indicator (10) will flash
red at a fast rate. Proceed as follows:
• Re-insert the battery (8).
• If the charging indicators continues
flashing red at a fast rate, use a different
battery to determine if the charging
process works properly.
• If the replaced battery charges correctly,
the original battery is defective and
should be returned to a service centre for
recycling.
• If the new battery gives the same
indication as the original battery, take the
charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to
determine that the battery is defective. If
the battery is too hot or too cold, the LED
will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use
forward (clockwise) rotation. For loosening
screws or removing a jammed drill bit, use
reverse (counterclockwise) rotation.
• To select forward rotation, push the
forward/reverse slider (2) to the left.

Содержание

Похожие устройства

ENGLISH Original instructions Insert the bit shaft into the chuck and firmly tighten the single sleeve chuck This tool is supplied with a screwdriver bit in the bit holder 7 To remove the screwdriver bit from the bit holder lift the bit from the recess To store the screwdriver bit firmly push it into the holder Warning Do not attempt to tighten drill bits or any other accessory by gripping the single sleeve chuck and turning the tool on Damage to the single sleeve chuck and personal injury may occur when changing accessories Use Warning Let the tool work at its own pace Do not overload Warning Before drilling into walls floors or ceilings check for the location of wiring and pipes Charging the battery fig A The battery needs to be charged before first use and whenever it fails to produce sufficient power on jobs that were easily done before The battery may become warm while charging this is normal and does not indicate a problem Warning Do not charge the battery at ambient temperatures below 10 C or above 40 C Recommended charging temperature approx 24 C Note The charger will not charge a battery if the cell temperature is below approximately 10 C or above 40 C The battery should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down The charging indicator 10 will blink The charge is complete when the charging indicator 10 switches to continuously on The charger and the battery can be left connected indefinitely The LED will switch on as the charger occasionally tops up the battery charge Charge discharged batteries within 1 week Battery life will be greatly diminished if stored in a discharged state Leaving the battery in the charger The charger and battery pack can be left connected with the LED glowing indefinitely The charger will keep the battery pack fresh and fully charged Charger diagnostics If the charger detects a weak or damaged battery the charging indicator 10 will flash red at a fast rate Proceed as follows Re insert the battery 8 If the charging indicators continues flashing red at a fast rate use a different battery to determine if the charging process works properly If the replaced battery charges correctly the original battery is defective and should be returned to a service centre for recycling If the new battery gives the same indication as the original battery take the charger to be tested at an authorised services centre Note It may take as long as 30 minutes to determine that the battery is defective If the battery is too hot or too cold the LED will alternately blink red fast and slow one flash at each speed and repeat Selecting the direction of rotation fig C To charge the battery 8 insert it into the charger 9 The battery will only fit into the charger in one way Do not force Be sure that the battery is fully seated in the charger For drilling and for tightening screws use forward clockwise rotation For loosening screws or removing a jammed drill bit use reverse counterclockwise rotation Plug in the charger and switch on at the mains To select forward rotation push the forward reverse slider 2 to the left

Скачать