Panasonic CQ-RG133W [8/23] Installation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Panasonic CQ-RG133W [8/23] Installation

Panasonic CQ-RG133W [8/23] Installation
1
2
3
4
E
N
G
L
I
S
H
CQ-RG133W
15
CQ-RG133W
14
E
N
G
L
I
S
H
11
Cautions:
• We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
• When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and
fingers.
Establish the rear connection of the unit.
After fixing Mounting Bolt t and Power Connector
y, fix the rear of the unit to the car body by either
method (a) or (b) shown on the previous page.
Insert Trim Plate i.
After installation reconnect the
negative (–) battery terminal.
First complete the electrical connections, and
then check them for correctness.(
a page 18)
Insert Mounting Collar q into the
dashboard, and bend the mounting
tabs out with a screwdriver.
The included Mounting Collar
q is designed specially for this
unit. Do not use it to attach any
other model.
y Power Connector
Engage the Mounting
Springs (
C) in the
mounting holes of the
Mounting Collar
q
firmly.
Mounting Spring
Mounting
Hole
Tab
q Mounting
Collar
Mounting Springs (C)
Mounting Holes
t Mounting Bolt
The tabs to be bent vary depending on the car.
To securely install the unit, fully bend a
number of the tabs so that there is no rattling.
Example:
Installation
Q’tyItemNo. Diagram
Installation Hardware
q
1
1
1
1
1
1
2
1
Mounting collar
Hex. nut (5 mmø)
Rear support strap
Tapping screw
(5 mmø
× 16 mm)
Mounting bolt (5 mmø)
Power connector
Dismounting plate
Trim plate
w
e
r
t
y
u
i
• Before installation, check the radio operation with
antenna and speakers.
• Disconnect the cable from the negative (–) battery
terminal (see caution below).
• Unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more
than 30°.
Dashboard Installation
Installation Opening
The unit can be installed
in any dashboard having
an opening as shown at
right. The dashboard
should be 4.5 mm - 6 mm thick in order to be able to
support the unit.
Installation Precautions
This product should be installed by a professional
installer, if possible.
In case of difficulty, please consult your nearest
authorized Panasonic Service Center.
1. This system is to be used only in a 12-volt, DC
battery system (car) with negative ground.
2. Follow the electrical connections carefully (
a page
18). Failure to do so may result in damage to the
unit.
3. Connect the power lead (red) after all other
connections are made.
4. Be sure to connect the battery lead (yellow) to the
positive terminal (+) of the battery or fuse block
(BAT) terminal.
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation
instructions of the respective equipment before
connecting it to this unit.
Preparation
30˚ or less
Caution: Do not disconnect the battery terminals of
a car with trip or navigational computer since all
user settings stored in memory will be lost.
Instead take extra care with installing the unit to
prevent shorts.
182 mm
53 mm
(a) Using the Rear Support Strap
(b) Using the Rubber Cushion (option)
E
N
G
L
I
S
H
10

Содержание

Похожие устройства

Ш20 1 X Installation Hardware Preparation хи rozm Installation Cautions We strongly recommend that you wear gloves for installation work to protect yourself from injuries Item No Before installation check the radio operation with Diagram Q ty 11 When bending the mounting tab of the mounting collar with a screwdriver be careful not to injure your hands and fingers antenna and speakers Disconnect the cable from the negative battery Ф Mounting collar 1 Hex nut 5 m mo 1 terminal see caution below Unit should be installed in a horizontal position with First complete the electrical connections and Insert then check them for correctness page 18 dashboard The included Mounting Collar the front end up at a convenient angle but not more Mounting and Collar bend into the the mounting tabs out with a screwdriver is designed specially for this 3 Rear support strap 1 unit Do not use it to attach any The tabs to be bent vary depending on the car other model To securely install the unit fully bend a Tapping screw 1 5mmo x16 mm num ber of the tabs so that there is no rattling Example Caution a car user Do not disconnect with trip or settings Instead stored take extra the battery navigational in care memory with terminals computer will installing since be the Mounting bolt 5 mmo 1 Power connector 1 Dismounting plate 2 of all Mounting lost unit to Z prevent shorts Dashboard Installation Tab Trim plate Collar 1 Power Connector Installation Opening The unit can be installed in any dashboard having an opening as shown at right The dashboard should be 4 5 mm 6 mm thick in order to be able to Mounting Holes support the unit Mounting Bolt Installation Precautions This product should be installed by a Establish the rear connection ot t unit professional installer if possible In case of After fixing Mounting Bolt and Power Connector difficulty please consult your 1 This system is to be Mounting Springs used only in a Follow the electrical connections method a or b shown on the previous page 12 volt DC Insert Trim Plate battery system car with negative ground 2 fix the rear of the unit to the car body by either nearest authorized Panasonic Service Center carefully page 18 Failure to do so may result in damage to the unit 3 Connect the power lead red after all other connections are made After installation reconnect negative battery terminal the 4 Be sure to connect the battery lead yellow to the positive terminal of the battery or fuse block BAT terminal 5 Insulate all exposed wires to prevent short circuiting 6 Secure all loose wires after installing the unit 7 Please carefully instructions of read the the respective operating and installation equipment before connecting it to this unit 14 CQ RG133W CQ RG133W 15

Скачать