![Gigabyte B460M GAMING HD — настройки энергопотребления и графики для компьютера [28/43]](/img/pdf.png)
Gigabyte B460M GAMING HD — настройки энергопотребления и графики для компьютера [28/43]
Превью страниц
Страница 28 /
43
![Gigabyte B460M GAMING HD [28/43] Soft off by pwr bttn](/views2/1666513/page28/bg1c.png)
& ErP
Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled)
Note: When this item is set to Enabled, the following functions will become unavailable: Resume by Alarm,
power on by mouse, and power on by keyboard.
& Soft-Off by PWR-BTTN
Congures the way to turn off the computer in MS-DOS mode using the power button.
Instant-Off Press the power button and then the system will be turned off instantly. (Default)
Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power
button is pressed for less than 4 seconds, the system will enter suspend mode.
& Resume by Alarm
Determines whether to power on the system at a desired time. (Default: Disabled)
If enabled, set the date and time as following:
Wake up day: Turn on the system at a specic time on each day or on a specic day in a month.
Wake up hour/minute/second: Set the time at which the system will be powered on automatically.
Note: When using this function, avoid inadequate shutdown from the operating system or removal of the
AC power, or the settings may not be effective.
& Power Loading
Enables or disables dummy load. When the power supply is at low load, a self-protection will activate causing
it to shutdown or fail. If this occurs, please set to Enabled. Auto lets the BIOS automatically congure this
setting. (Default: Auto)
& RC6(Render Standby)
Allows you to determine whether to let the onboard graphics enter standby mode to decrease power
consumption. (Default: Enabled)
& AC BACK
Determines the state of the system after the return of power from an AC power loss.
Memory The system returns to its last known awake state upon the return of the AC power.
Always On The system is turned on upon the return of the AC power.
Always Off The system stays off upon the return of the AC power. (Default)
IO Ports
& Initial Display Output
Species the rst initiation of the monitor display from the installed PCI Express graphics card or the onboard
graphics.
IGFX
(Note)
Sets the onboard graphics as the rst display.
PCIe 1 Slot Sets the graphics card on the PCIEX16 slot as the rst display. (Default)
& Internal Graphics
Enables or disables the onboard graphics function. (Default: Auto)
& DVMT Pre-Allocated
Allows you to set the onboard graphics memory size. Options are: 0M~512M. (Default: 64M)
& DVMT Total Gfx Mem
Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX.
(Default: 256M)
& Aperture Size
Allows you to set the maximum amount of system memory that can be allocated to the graphics card.
Options are: 128MB, 256MB, 512MB, 1024MB, and 2048MB. (Default: 256MB)
& Onboard LAN Controller
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
(Note) This item is present only when you install a CPU that supports this feature.
- 28 -
Содержание
304- User s manual
- B460m gaming hd
- Rev 1001
- Disclaimer
- Identifying your motherboard revision
- Copyright
- Chapter 2 bios setup 9
- Chapter 1 hardware installation
- Table of contents
- Chapter 3 appendix 7
- B460m gaming hd motherboard layout
- B460m gaming hd motherboard layout
- B460m gaming hd
- User s manual 5 i o shield
- Motherboard driver disc 5 two sata cables
- Box contents
- B460m gaming hd motherboard
- Chapter 1 hardware installation
- 1 installation precautions
- 2 product specifications
- 2 productspecifications
- Installing the cpu
- Dualchannelmemoryconfiguration
- 4 installing the memory
- 3 installing the cpu
- Usb 3 gen 1 port
- Ps 2 keyboard and ps 2 mouse port
- Hdmi port
- D sub port
- 6 back panel connectors
- 5 installing an expansion card
- Line out front speaker out green
- Line in rear speaker out blue
- Audio jack configurations
- User to change the function for each jack through the audio driver
- Usb 2 1 port
- To configure 7 channel audio you need to open the audio software and select device
- The usb port supports the usb 2 1 specification use this port for usb devices
- The mic in jack
- The line out jack use this audio jack for a headphone or 2 channel speaker
- The line in jack use this audio jack for line in devices such as an optical drive walkman etc
- The integrated hd high definition audio provides jack retasking capability that allows the
- The gigabit ethernet lan port provides internet connection at up to 1 gbps data rate the following describes the states of the lan port leds
- Rj 45 lan port
- Please visit gigabyte s website for details on configuring the audio software
- Playback device to change the default setting first
- Mic in center subwoofer speaker out pink
- 7 internal connectors
- 4 cpu_fan sys_fan fan headers
- 2 atx_12v_2x4 atx 2x4 12v power connector and 2x12 main power connector
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start
- Overheating overheating may result in damage to the cpu or the system may hang
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis
- The header can be used to connect a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m
- Select the proper hole for the mounting clip according to the length of the m ssd to be installed
- Pin no definition
- M2m_pch m socket 3 connector
- Led_c rgb led strip header
- For how to turn on off the lights of the led strip please visit the unique features webpage of gigabyte s website
- Follow the steps below to correctly install an m ssd in the m connector step 1 locate the proper mounting hole for the m ssd to be installed and then install the mounting clip first step 2 slide the m ssd into the connector at an angle step 3 press the m ssd down and then secure it by pressing the clip pin into the mounting hole
- Connect your rgb led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 12v of this header incorrect connection may lead to the damage of the led strip
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices
- The m connector supports m sata ssds or m pcie ssds and supports sata raid configuration please note that an m pcie ssd cannot be used to create a raid set with a sata hard drive refer to chapter 3 configuring a raid set for instructions on configuring a raid array
- Pled pwr_led power led
- Speak speaker
- Connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup
- Connects to the power status indicator on the chassis front panel the led is on when the system is operating the led is off when the system is in s3 s4 sleep state or powered off s5
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the inte
- The front panel design may differ by chassis a front panel module mainly consists of power switch reset switch power led hard drive activity led speaker and etc when connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly
- Sata3 0 1 2 3 sata 6gb s connectors
- Res reset switch connects to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart
- Pw power switch connects to the power switch on the chassis front panel you may configure the way to turn off your system using the power switch refer to chapter 2 bios setup settings platform power for more information
- Nc no connection
- Hd hard drive activity led connects to the hard drive activity led on the chassis front panel the led is on when the hard drive is reading or writing data
- F_panel front panel header
- Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below note the positive and negative pins before connecting the cables
- Ci chassis intrusion header connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed this function requires a chassis with a chassis intrusion switch sensor
- Chipset supports raid 0 raid 1 raid 5 and raid 10 refer to chapter 3 configuring a raid set for instructions on configuring a raid array
- To enable hot plugging for the sata ports refer to chapter 2 bios setup settings io ports sata and rst configuration for more information
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer
- From the power outlet to prevent damage to the usb bracket
- F_usb1 f_usb2 usb 2 1 headers
- F_u32 usb 3 gen 1 header
- F_audio front panel audio header
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord
- Data input 11 nc
- The com header can provide one serial port via an optional com port cable for purchasing the optional com port cable please contact the local dealer
- The cmos values
- Com serial port header
- Spi_tpm trusted platform module header
- Clr_cmos clear cmos jumper
- Short clear cmos values
- Clk 12 rst
- Power 3 v 8 gnd
- Always turn off your computer and unplug the power cord from the power outlet before clearing
- Pin no definition pin no definition
- After system restart go to bios setup to load factory defaults select load optimized defaults or
- Open normal
- Nsout 8 ncts
- Nsin 7 nrts
- No pin 9 irq
- Ndtr 9 nri
- Ndcd 6 ndsr
- Nc 10 nc
- Manually configure the bios settings refer to chapter 2 bios setup for bios configurations
- Gnd 10 no pin
- You may connect an spi tpm trusted platform module to this header
- Data output 7 chip select
- Use this jumper to clear the bios configuration and reset the cmos values to factory defaults to clear the cmos values use a metal object like a screwdriver to touch the two pins for a few seconds
- Bat battery
- Chapter 2 bios setup
- 1 startup screen
- Advanced mode function keys
- 2 the main menu
- 3 favorites f11
- Igp rati
- Hyper threading technology
- Fclk frequency for early power on
- Cpu over temperature protectio
- Cpu clock ratio
- Avx offse
- Advanced cpu settings
- 4 tweaker
- Ring ratio
- No of cpu cores enabled
- Speed shift technology
- Ring to core offset down bin
- Race to halt rth
- Intel r turbo boost technology
- Intel r turbo boost max technology 3
- Intel r speed shift technology inte
- Energyefficientturb
- D c states control
- D active turbo ratios
- Cpu thermal monito
- Cpu flex ratio settings
- Cpu flex ratio override
- Cpu enhanced halt c1e
- Cpu eist functio
- Voltage optimization
- Turbo ratio
- Package power limit tdp watts package power limit time
- Package c state limi
- Dram power limit dram power limit time
- D turbo power limits
- D turbo per core limit contro
- Core current limit amps
- C8 state suppor
- C6 c7 state support
- C3 state suppor
- C10 state suppor
- Memory boot mode
- Extremememoryprofile x m p
- Channel interleaving
- Advanced memory settings
- System memory multiplier
- Spd info
- Realtime memory timing
- Rank interleaving
- Memory ref clock
- Memory odd ratio 100 133 or 200 266
- Memory multiplier tweaker
- Memory enhancement settings
- Memory channel detection message
- Power on by keyboard
- Platform power management
- Platform power
- Peg aspm
- Pch aspm
- Dmi aspm
- 5 settings
- Power on password
- Power on by mouse
- Soft off by pwr bttn
- Resume by alarm
- Rc6 render standby
- Power loading
- Onboard lan controller
- Io ports
- Internal graphics
- Initial display output
- Dvmt total gfx mem
- Dvmt pre allocated
- Aperture size
- Ac back
- Legacy usb support
- Xhci hand off
- Audio controller
- Usbconfiguration
- Above 4g decoding
- Usb mass storage driver support
- Superioconfiguration
- Serial port
- Pxe boot wait time
- Networkstackconfiguration
- Network stack
- Media detect count
- Mass storage devices
- Ipv6 pxe support
- Ipv6 http support
- Ipv4 pxe support
- Ipv4 http support
- Ioapic 24 119 entries
- Software guard extensions sgx
- Sataandrstconfiguration
- Sata mode selection
- Sata controller s
- Realtek pcie gbe family controller
- Port 0 1 2 3
- Nvmeconfiguration
- Miscellaneous
- Max link speed
- Leds in system power on state
- Intel platform trust technology ptt
- Hot plug
- Ez raid
- Configuredasesata
- Aggressive lpm support
- 3dmark01 enhancement
- Temperature warning control
- Temperature interval
- Temperature
- Smart fan 5
- Reset case open status
- Pc health status
- Monitor
- Flow rate
- Fan stop
- Fan speed control
- Fan speed
- Fan fail warning
- Fan control use temperature input
- Fan control mode
- Cpu vcore cpu vccsa dram channel a b voltage 3 v 5v 12v cpu vaxg
- Case open
- Trusted computing
- System time
- System language
- System date
- Q flash
- Plug in devices info
- Access level
- 6 system info
- Vga support
- Security option
- Sata support
- Full screen logo show
- Fast boot
- Bootup numlock state
- Boot option priorities
- 7 boot
- Windows 10 features
- Usb support
- Storage boot option control
- Ps2 devices support
- Other pci devices
- Next boot after ac power loss
- Network stack driver support
- Mouse speed
- Lan pxe boot option rom
- Csm support
- User password
- Secure boot
- Preferred operating mode
- Administrator password
- Boot override
- 8 save exit
- Saveprofiles
- Save exit setup
- Loadprofiles
- Load optimized defaults
- Exit without saving
- Raid levels
- Configuringtheonboardsatacontroller
- Chapter 3 appendix
- C 1 using ez raid
- Before you begin please prepare the following items
- B configuringsatacontrollermodeinbiossetup
- A installing sata hard drive s in your computer
- 1 configuringaraidset
- 1 configuring a raid set
- C 3 configuringlegacyraidrom
- C 2 uefiraidconfiguration
- System requirements
- Memory
- Installing the operating system
- Installation guidelines a 1 installation in ahci mode
- Install the raid driver and operating system
- 2 installing an intel optane memory
- 2 installing an inte
- A 2 installation in intel rst premium with intel optane system acceleration mode
- 3 drivers installation
- United states of america federal communications commission statement
- Regulatory notices
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com
- Gigabyte esupport
- Contact us
Похожие устройства
-
Gigabyte B760M D3H DDR4Инструкция пользователя -
Gigabyte GA-880GM-D2HИнструкция по работе -
Gigabyte Z890 EAGLEЭксплуатационная инструкция -
Gigabyte Z890 EAGLE WIFI7Инструкция по применению
-
Gigabyte H610M S2HРуководство по использованию -
Gigabyte Z790 AORUS MASTER XРуководство по работе с устройством -
Gigabyte B660M GAMINGИнструкция пользователя -
Gigabyte B550M DS3H ACИнструкция по работе -
Gigabyte GA-Q87TNРуководство по настройке -
Gigabyte GA-H87TNИнструкция по работе
-
Gigabyte GA-B85TNРуководство пользователя
-
Gigabyte GA-H81TNИнструкция по применению
Узнайте, как оптимизировать энергопотребление вашего компьютера с помощью различных настроек BIOS. Настройте функции включения, отключения и графики для повышения эффективности.