![MEAN WELL RCP-1000-48-C [5/8] Series](/img/pdf.png)
MEAN WELL RCP-1000-48-C [5/8] Series
![MEAN WELL RCP-1UT [5/8] Series](/views2/1678767/page5/bg5.png)
Derating Curve
CN500 Pin No. Assignment
CN500 IN/OUT Connector pins function description
Static Characteristics
INPUT VOLTAGE (VAC) 60Hz
90 95 100 115 264
90
100
80
70
60
50
40
AMBIENT TEMPERATURE ( )℃
20
40
60
80
100
-20 0 10 20 30 40 50 60 70
RCP
seri e s
Connector Pin No. Assignment(CN500) : D-Type Right Angle 25 positions
Pin No. Pin No. Pin No. Pin No. Pin No.
2
1
3
4
5
Assignment Assignment Assignment Assignment Assignment
AC-OK-A
ON/OFF-A
DC-OK-A
V-TRIM-A
T-ALARM-A
7
13
9
8
10
14
15
6
12
11 16
17
23
21
22
25
18
19
20
24
AC-OK-B
DC-OK-B
ON/OFF-B
+5V-AUX
GND-AUX
NC
CS
ON/OFF-C
V-TRIM-B
T-ALARM-B
AC-OK-C
DC-OK-C
SCL
-S
+V
-V
V-TRIM-C
T-ALARM-C
+S
SDA
Pin No. Function
Description
1,8,15
2,9,16
3,10,17
4,11,18
5,12,19
7
23
25
14
6
ON/OFF
AC-OK
DC-OK
V-TRIM
T-ALARM
GND-AUX
SCL
-V
CS
+5V-AUX
Each unit can separately turn the output on and off by electrical or dry contact between ON/OFF A,B,C(pin 1,8,15) and -S(pin 21). Short: ON, Open:OFF.
Low : When the input voltage is 82Vrms +/-4V. High : when the input voltage in 82Vrms +/-4V.≧ ≦
High : When the Vout 80%+/-5%. Low : When Vout 80%+/-5%≦ ≧
Connection for output voltage trimming. The voltage can be trimmed within its defined range.
High : When the internal temperature is within safe limit. Low : 10 below the thermal shut down limit.℃
Auxiliary voltage output GND. The signal return is isolated from the output terminals (+V & -V).
Serial clock used in the I C interface option. Refer to the I C interface description.
Negative output voltage. For local sense use only, can't be connected directly to the load.
Current sharing signal. When units are connected in parallel, the CS pins of the units should be connected to allow current balance
between units.
Auxiliary voltage output, 4.3~5.3V, referenced to GND-AUX(pin 7). The maximum load current is 0.3A. This output has the built-in
"Oring diodes" and is not controlled by the remote ON/OFF control.
2 2
1000 ~ 3000W Front End Power System
Fi le Name:RCP series-SPEC 2015-02-11
20
21
+S
-S
Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be twisted in pair to
minimize noise pick-up effect. The maximum line drop compensation is 0.5V.
Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be twisted in pair to
minimize noise pick-up effect. The maximum line drop compensation is 0.5V.
22 +V
Positive output voltage. For local sense use only, can't be connected directly to the load.
24 SDA
Serial data used in the I C interface option. Refer to the I C interface description.
2 2
Содержание
- Series 1
- 3000w front end power system 2
- Series 2
- Specification rack system 2
- 3000w front end power system 3
- Block diagram 3
- Mechanical specification single unit 3
- Series 3
- 3000w front end power system 4
- Mechanical specification rack system 4
- Series 4
- 3000w front end power system 5
- Cn500 in out connector pins function description 5
- Cn500 pin no assignment 5
- Derating curve 5
- Series 5
- Static characteristics 5
- 3000w front end power system 6
- Function manual 6
- Series 6
- 3000w front end power system 7
- Address dip switch setting 7
- Addressing a0 a1 a2 7
- Front panel indicators corresponding signal at function pins 7
- I c bus interface option 7
- Rcp 1000 24 7
- Rcp 1000 48 7
- Series 7
- The dip switch down position is logic level 1 and the up position is level 0 address are applicable when modules rcp 1000 i c function are used 7
- 3000w front end power system 8
- A d scaling 8
- Analog function are provided by a single pcf8591 4 channel 8 bit a d converter when this device is read by the i c bus controller it provides an 8 bit 8
- Analog function read only 8
- Digital function are provided by a pcf8574 8 bit i o port device when this device is read by the i c bus controller a single 8 bit word provides the following information 8
- Digital function read only 8
- Eeprom function read only 8
- Eeprom slave address 8
- Pcf8574 slave address 8
- Pcf8591 control byte 8
- Pcf8591 slave address 8
- Series 8
- The eeprom is a 2048 bit 256 byte device which is preprogrammed at the factory with the following data 8
- The voltage reading is made inside the power supply unit before the oring diode and is typically 0 v higher than the actual output voltage the following table for the scaling should be employed 8
- Value byte value x resolution 8
- Word with the following information 8
Похожие устройства
- MEAN WELL RCP-1UI Инструкция по эксплуатации
- MEAN WELL RCP-1UI Инструкция язык en
- MEAN WELL RCP-1UI Каталог
- MEAN WELL RCP-1UI Data Sheet
- MEAN WELL RCP-1UT Инструкция по эксплуатации
- MEAN WELL RCP-1UT Инструкция язык en
- MEAN WELL RCP-1UT Каталог
- MEAN WELL RCP-1UT Data Sheet
- MEAN WELL RCP-2000-12 Инструкция по эксплуатации
- MEAN WELL RCP-2000-12 Инструкция язык en
- MEAN WELL RCP-2000-12 Каталог
- MEAN WELL RCP-2000-12 Data Sheet
- MEAN WELL RCP-2000-24 Инструкция по эксплуатации
- MEAN WELL RCP-2000-24 Инструкция язык en
- MEAN WELL RCP-2000-24 Каталог
- MEAN WELL RCP-2000-24 Data Sheet
- MEAN WELL RCP-2000-48 Инструкция по эксплуатации
- MEAN WELL RCP-2000-48 Инструкция язык en
- MEAN WELL RCP-2000-48 Каталог
- MEAN WELL RCP-2000-48 Data Sheet