MEAN WELL CEN-100-42 Data Sheet онлайн
THD< 20% when output loading 75% at 115VAC/230VAC input and output loading 80% at 277VAC input≧≧
TOTAL HARMONIC DISTORTION
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
19 units (circuit breaker of type B) / 19 units (circuit breaker of type C) at 230VAC
SPECIFICATION
MODEL CEN-100-20 CEN-100-24 CEN-100-30 CEN-100-36 CEN-100-54CEN-100-48CEN-100-42
DC VOLTAGE
CURRENT RANGE
RATED POWER
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP TIME
VOLTAGE RANGE
Note.4
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER CURRENT
SHORT CIRCUIT
OVER VOLTAGE
OVER TEMPERATURE
20V 24V 30V 36V 54V48V42V
0 ~ 4.8A 0 ~ 4A 0 ~ 3.2A 0 ~ 2.65A 0 ~ 1.77A0 ~ 2A0 ~ 2.28A
96W 96W 96W 95.4W 95.58W96W95.76W
2.0Vp-p 2.7Vp-p 3Vp-p 3.6Vp-p 5Vp-p4.6Vp-p4Vp-p
±10%
±3.0%
±5.0%
90 ~ 295VAC 127 ~ 417VDC
47 ~ 63Hz
PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
88% 89% 90% 90% 91%91%90%
22.8 ~ 26V 28 ~ 32V 34 ~ 38V 41 ~ 46V 59 ~ 68V54 ~ 60V47 ~ 52V
1.4A/115VAC 0.7A/230VAC 0.5A/277VAC
COLD START 45A(twidth=85 s measured at 50% Ipeak) at 230VACμ
<0.75mA / 240VAC
95 ~ 110%
Protection type :
Constant current limiting, recovers automatically after fault condition is removed
Hiccup mode, recovers automatically after fault condition is removed
-30 ~ +70 (Refer to "Derating Curve")℃
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
519.5Khrs min. MIL-HDBK-217F (25 )℃
195*62.5*40.5mm (L*W*H)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. lease refer to "DRIVING METHODS OF LED MODULE".
P
6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
Protection type : Shut down o/p voltage, re-power on to recover
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage, re-power on to recover
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
UL8750, CSA C22.2 No. 250.0-08(except for 48V, 54V), TUV EN61347-1, EN61347-2-13, IP66, J61347-1, J61347-2-13 approved
I/P-O/P, I/P-FG, O/P-FG: >100M Ohms / 500VDC / 25 / 70% RH℃
SAFETY STANDARDS
Compliance to EN55015, EN61000-3-2 Class C ( 65% load) ; EN61000-3-3≧
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV), criteria B
13 ~ 20V 15.6 ~ 24V 19.5 ~ 30V 23.4 ~ 36V 35.1 ~ 54V31.2 ~ 48V27.3 ~ 42V
RATED CURRENT 4.8A 4A 3.2A 2.65A 1.77A2A2.28A
17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 49 ~ 58V43 ~ 53V37 ~ 46VVOLTAGE ADJ. RANGE
(SVR1)
CURRENT ADJ. RANGE(SVR2)
3.12 ~ 4.8A 2.6 ~ 4A 2.08 ~ 3.2A 1.72 ~ 2.65A 1.15 ~ 1.77A
1.3 ~ 2A1.48 ~ 2.28A
100W Single Output LED Power Supply
CEN-100 series
Universal AC input / Full range (up to 295VAC)
Protections: Short circuit / Over current / Over voltage / Over temperature
Output voltage and constant current level adjustable
Built-in active PFC function
IP66 design for indoor or outdoor installations
Class 2 power unit
Cooling by free air convection
100% full load burn-in test
High reliability
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
Suitable for dry / damp / wet locations
3 years warranty
■
Features :
EMC IMMUNITY
EMC EMISSION
IP66
110
SELV
..
F
( except for 48V,54V )( for 48V,54V only)
0.6Kg;24pcs/15.4Kg/1.29CUFT
500ms / 230VAC 1200ms / 115VAC at full load
CONSTANT CURRENT REGION
Note.5
File Name:CEN-100-SPEC 2015-05-28
Содержание
- Cen 10 1
- Hiccup mode recovers automatically after fault condition is removed 1
- Series 1
- W single output led power supply 1
- Ac l brown ac n blue 2
- Block diagram 2
- Cen 10 2
- Derating curve static characteristics 2
- Mechanical specification 2
- Series 2
- Sjtw 18awg 3c 2
- Svt 18awg 2c 2
- T case 2
- V black v red 2
- W single output led power supply 2
- Ψ 4 4pl 2
- Cen 10 3
- Constant current mode 3
- Series 3
- W single output led power supply 3
Похожие устройства
- MEAN WELL CEN-100-48 Инструкция по эксплуатации
- MEAN WELL CEN-100-48 Инструкция язык en
- MEAN WELL CEN-100-48 Каталог
- MEAN WELL CEN-100-48 Data Sheet
- MEAN WELL CEN-60-12 Инструкция по эксплуатации
- MEAN WELL CEN-60-12 Инструкция язык en
- MEAN WELL CEN-60-12 Каталог
- MEAN WELL CEN-60-12 Data Sheet
- MEAN WELL CEN-60-15 Инструкция по эксплуатации
- MEAN WELL CEN-60-15 Инструкция язык en
- MEAN WELL CEN-60-15 Каталог
- MEAN WELL CEN-60-15 Data Sheet
- MEAN WELL CEN-60-20 Инструкция по эксплуатации
- MEAN WELL CEN-60-20 Инструкция язык en
- MEAN WELL CEN-60-20 Каталог
- MEAN WELL CEN-60-20 Data Sheet
- MEAN WELL CEN-60-24 Инструкция по эксплуатации
- MEAN WELL CEN-60-24 Инструкция язык en
- MEAN WELL CEN-60-24 Каталог
- MEAN WELL CEN-60-24 Data Sheet