![Vitek VT-1356 [5/6] English](/img/pdf.png)
Vitek VT-1356 [5/6] English
![Vitek VT-1356 [5/6] English](/views2/1007253/page5/bg5.png)
КОМПЛЕКТАЦИЯ
ПРАВИЛА БЕЗОПАСНОГО ИСПОЛЬЗОВАНИЯ
Просьба внимательно прочитать настоящее руководство по эксплуатации перед
использованием машинки.
Подготовка к использованию:
1. Извлеките машинку из упаковки. Храните упаковку в пригодном для
использования состоянии до тех пор, пока не убедитесь в надлежащем
функционировании машинки.
2. З
АПРЕЩАЕТСЯ подключать машинку к сети питания, если она не готова к
использованию.
Подгонка лезвий
Подгонка лезвий должна осуществляться каждый раз после снятия лезвий для
чистки или замены.
Для того чтобы осуществить подгонку лезвий, необходимо позиционно
совместить положение всех зубьев верхнего (керамического) и нижнего
(выполненного из нержавеющей стали) лезвий. Край верхних зубьев должен
заходить за нижние лезвие примерно на 1.2 мм.
В случае неправильной подгонки лезвий, необходимо выключить машинку и
отсоединить ее от сети питания. Ослабьте крепежные болты и отрегулируйте
положение лезвий. После подгонки лезвий, затяните крепежные болты.
Благодаря своей конструкции совместному использованию керамического
лезвия и лезвия из нержавеющей стали приобретенная Вами машинка не
нуждается в смазке. Вместе с тем, для поддержания лезвий в идеальном
состоянии, рекомендуется подвергать их периодической смазке.
РУССКИЙ
8
• Relax and work precisely. Only use short strokes. Do not immediately cut the
entire side or back of the head, but work gradually around the entire head.
• It is better to remove a little bit each time You can always cut more later.
• Before you begin and while you are working, comb the hair back to the desired
style.
• Use the clipper only on dry hair.
STEP 1 THE NECK AREA
• Attach comb attachment 3 mm or 6 mm. Hold the clipper with the cutting side up
and start cutting at the centre of the base of the neck. Hold the clipper firmly but
gently against the skin and clip in a straight upward direction.
• Move the clipper gradually upward and outward through the hair, removing only
small bits at a time. While cutting, move the head on the dipper gradually away
from the head (toward you). Then cut the back area from the bottom of the neck
to above the ears.
STEP 2 BACK OF THE HEAD
• Change to the next longest comb attachment 9 mm or 12 mm and cut the back of
the head.
STEP 3 SIDE OF THE HEAD
• Use one of the shorter combs (3 mm or 6mm) to cut sideburns (the hair right in
front of the ears). The tapered combs are specially made for clipping along the
sides of the head.
• If you are standing behind the person whose hair is to be cut, the comb marked
"Right" is for the left side of their head, and vice verse.
• For even cutting, move the clippers over the side of the their head, from front to
back.
STEP 4 T
OP OF THE HEAD
• Using comb attachment 9 mm or 12 mm, cut top of head from back to front
against the direction in which the hair normally grows.
• Comb attachment 3mm or 6mm are used to achieve a dose crew cut.
• For longer hair on top, use the comb provided and lift hair on the top of the head.
Cut with the clipper over the comb, or hold the hair between the ringers to lift it
and cut it to desired length. Always work from the back of the head. You can cut
the hair shorter gradually by reducing the space between the comb/fingers, and
the head.
ENGLISH
5
Vt-1356.qxd 18.12.03 12:57 Page 10
Содержание
- Модель vt 1356 1
- Features 2
- Hair clipper 1 ceramic blade 2 on off switch 3 blade adjustment lever 4 steel blade 5 pivot cord 2
- Vt 1356 qxd 18 2 3 12 57 page 4 2
- Русский english 2
- Before using for the first time before using the appliance for the first time read the instructions and keep it for later reference when you use the clipper for the first time cut only small portions of hair until you are accustomed to the cutting length with a certain comb attachment first try the longest comb attachment 12 mm if you want a shorter cut use the comb 6 mm experience will soon tell you which comb attachment to use for the result you desired after the hair has been combed into its natural direction proceed as fol lows to achieve a smooth layered hairstyle 3
- English 3
- Important safeguard for safety reason this appliance may not be used within a distance of one meter from a bathtub or shower not from a sink filled with water never hold it under water if an appliance has fallen into water never try to grab it first pull the lug from the electrical outlet with children or the infirm use the appliance only under supervision treat the cutting blades with care do not bump them against hard objects or allow them to fall do not use if the blades are damaged do not use the appliance if it is damaged or the cord is damaged 3
- Includes accessories 3
- Vt 1356 qxd 18 2 3 12 57 page 6 3
- Русский 3
- Adjustment screw 4
- Adjustment screw is located on the side of the clippers if the clippers do not work perfectly turn this screw to the right until a rattling sound can be heard then turn the screw back to the left until this sound just stops note never turn the adjustment screw completely out 4
- Before you start cutting check the clippers make sure that they are free of hair and lint spread drop of oil on blades switch on the clipper and check it runs smoothly place a towel around the person s neck seat the person so their head is approximately at your eye level this allows ease of visibility while cutting and a relaxed control of the unit first comb the hair so that it falls in its natural direction hold the clipper as com fortably as possible in your hand 4
- Blades adjustment level 4
- Click the comb attachment onto the cutting blades first hook them on from the top and press on the bottom remove them by pulling up the lip on the bottom of the comb 4
- Comb attachment 4
- English 4
- Instruction for use first remove the guard from the cutting blades plug the clipper into electrical outlet switch on the clipper after using always switch off the clipper first and then pull out of the electrical socket replace the blade guard on the cutting blades if the clipper does not cut well the swing arm must be checked plug in the clipper and switch it on with a coin or large screwdriver turn the large plastic screw on the side clockwise until the clipper makes a clattering sound then turn the adjustment screw back until the clattering stops 4
- Move the adjustment level to change the cutting length up for a shorter length down for longer length 4
- Vt 1356 qxd 18 2 3 12 57 page 8 4
- Русский 4
- English 5
- Vt 1356 qxd 18 2 3 12 57 page 10 5
- Русский 5
- English 6
- Vt 1356 qxd 18 2 3 12 57 page 12 6
- Русский 6
Похожие устройства
- Xdevice microMAP-Indianapolis HIT-4-A5-FM Инструкция по эксплуатации
- Bosch MCM 2054 Инструкция по эксплуатации
- A4Tech G7-300 Инструкция по эксплуатации
- Philips SHS4700 ⁄ 00 Инструкция по эксплуатации
- Korg GT120 Инструкция по эксплуатации
- Интерскол СМ-60/150 Инструкция по эксплуатации
- Vitek VT-1355 Инструкция по эксплуатации
- Korg GT4 Инструкция по эксплуатации
- A4Tech G7-200 Инструкция по эксплуатации
- Globalsat GH-625M Инструкция по эксплуатации
- Bosch MCM 5514 Инструкция по эксплуатации
- Festool TS 55 EBQ-Plus-FS 561508 Инструкция по эксплуатации
- Vitek VT-1354 Инструкция по эксплуатации
- Korg LCA120 Инструкция по эксплуатации
- Globalsat GH-625B Инструкция по эксплуатации
- A4Tech G7-540 Инструкция по эксплуатации
- Bosch MCM 5525 Инструкция по эксплуатации
- Philips SHP8500 ⁄ 00 Инструкция по эксплуатации
- Festool TS 75 EBQ 561184 Инструкция по эксплуатации
- Vitek VT-1353 Инструкция по эксплуатации
Скачать
Случайные обсуждения