![Icom IC-M1 [21/24] Troubleshooting](/img/pdf.png)
Icom IC-M1 [21/24] Troubleshooting
![Icom IC-M1 [21/24] Troubleshooting](/views2/1074608/page21/bg15.png)
TROUBLESHOOTING
8
18
PROBLEM POSSIBLE CAUSE SOLUTION REF.
No power comes ON.
•The battery is exhausted.
•Bad connection to the battery pack.
•Recharge the battery pack.
•Check the connection to the transceiver.
p. 15
p. 2
No sound comes from
the speaker.
•Squelch level is too deep.
•Volume level is too low.
•Speaker has been exposed to water.
•Set squelch to the threshold point.
•Set [OFF/VOL] to a suitable level.
•Drain water from the speaker.
p. 6
p. 7
—
Transmitting is impossi-
ble, or high power can-
not be selected.
•Some channels are for low power or re-
ceive only.
•The battery is exhausted.
•The output power is set to low or extra low.
•Change channels.
•Recharge the battery pack.
•Push [H/L] to select high power.
pgs.
5, 7
p. 15
p. 7
The displayed channel
cannot be changed.
•Lock function is activated. •Push [H/L•
LOCK] for 1 sec. to cancel the
function.
p. 6
Scan does not start. •“TAG” channel is not programmed. •Set the desired channels as “TAG” chan-
nels.
p. 12
Scan starts automati-
cally.
•Auto scan function is activated. •Cancel the auto scan function in SET
mode.
p. 14
No beep sounds. •Beep tone is turned OFF. •Turn the beep tone ON in SET mode. p. 13
Receive signal cannot
be understood.
•Optional voice scrambler is turned OFF.
•Scramble code is not set correctly.
•Turn the optional voice scrambler ON.
•Reset the scramble code.
p. 8
p. 8
Содержание
- Instruction manual 1
- Vhf marine transceiver 1
- Be careful 2
- Cautions 2
- Important 2
- Make sur 2
- R warning 2
- Read all instruction 2
- Save this instruction manual 2
- Table of contents 3
- I front panel 4
- Panel description 4
- I top and side panels 5
- Panel description 5
- I function display 6
- Panel description 6
- Basic operation 7
- I operating rules 7
- Priorities 7
- Privacy 7
- Radio licenses 7
- Basic operation 8
- D channel 16 8
- D channel 9 call channels 8
- D u s a canadian and international channels 8
- I channel selection 8
- Basic operation 9
- D weather channels 9
- I adjusting the squelch level 9
- I lock function 9
- Basic operation 10
- Caution 10
- I receiving and transmitting 10
- Important to maximize the readability of your trans mitted signal pause a few sec after pushing ptt hold the microphone 4 to 6 inches 10 to 15 cm from your mouth and speak at a normal voice level 10
- Note the transceiver has power save function to con serve the battery power and cannot be turned off the power save function activates automatically when no sig nal is received for 5 sec 10
- Push and hold ptt to transmit then speak into the mi crophone 10
- Push h l to select the output power if necessary 10
- Release ptt to receive 10
- Rotate off vol clockwise to turn power on then set to the 10 o clock position 10
- Rotate the channel selector to select the desired channel 10
- Transmitting without an antenna may dam age the transceiver 10
- Basic operation 11
- D activating the scrambler 11
- D programming scramble codes 11
- I optional voice scrambler operation 11
- Basic operation 12
- I automatic backlighting 12
- I call channel programming 12
- Dualwatch monitors channel 16 while you are receiving an other channel tri watch monitors channel 16 and the call channel while receiving another channel 13
- Dualwatch tri watch 13
- Dualwatch tri watch simulation 13
- Example operating tri watch on int channel 07 13
- I description 13
- I operation 13
- Momentarily to start dualwatch push 13
- Select the desired operating channel 2 push d 13
- To cancel dualwatch tri watch push d 13
- Tri for 1 sec to start tri watch 13
- I scan types 14
- Scan operation 14
- I setting tag channels 15
- I starting a scan 15
- Scan operation 15
- D automatic backlightin 16
- D beep ton 16
- I set mode items 16
- I set mode programming 16
- Set mode 16
- D auto scan functio 17
- D scan resume time 17
- D scan type selectio 17
- D weather alert functio 17
- Set mode 17
- Battery charging 18
- Caution 18
- D recycling information 18
- I battery cautions 18
- I battery charging 18
- Battery charging 19
- D attaching the ad 58 to a wall 19
- D charging with the ad 58 19
- D charging with the optional bc 119 ad 69 19
- D installing the ad 69 to the bc 119 19
- Caution 20
- D belt clip 20
- D flexible antenna 20
- D handstrap 20
- D unpacking 20
- Unpacking and accessory attachment 20
- Troubleshooting 21
- Channel list 22
- Low power only 22
- Receive only 22
- D battery packs 23
- I options 23
- I specifications 23
- Specifications and option 23
- 9 16 kamihigashi hirano ku osaka 547 japan 24
Похожие устройства
- Bimatek IR400 Инструкция по эксплуатации
- Brother DS-140 Инструкция по эксплуатации
- Icom IC-M1V Инструкция по эксплуатации
- Bimatek IR401 Инструкция по эксплуатации
- Brother Innov-is 20 Инструкция по эксплуатации
- Icom IC-M3A Инструкция по эксплуатации
- Bimatek IR300 Инструкция по эксплуатации
- Icom IC-M2A Инструкция по эксплуатации
- Bimatek IR301 Инструкция по эксплуатации
- Icom IC-M34 Инструкция по эксплуатации
- Liebherr KBs 3864-20 Инструкция по эксплуатации
- Icom IC-M15 Инструкция по эксплуатации
- Liebherr CTsl 2451-20 Инструкция по эксплуатации
- Icom IC-M45A Инструкция по эксплуатации
- Bosch KGV36VW20R Инструкция по эксплуатации
- Icom IC-M56 Инструкция по эксплуатации
- Hotpoint-Ariston ECF 2014 L Инструкция по эксплуатации
- Icom IC-M304 Инструкция по эксплуатации
- Siemens KG36VXW20R Инструкция по эксплуатации
- Jura Impressa XS90 Инструкция по эксплуатации