Metabo WX 2000 [16/108] Troubleshooting
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Metabo WX 2000 [16/108] Troubleshooting

Metabo WX 2000 [16/108] Troubleshooting
ENGLISHen
16
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands at the intended handles, take a secure
stance and concentrate on the work.
See illustration A on page 2.
Torque activation
Switching on:
Slide the lock (4) in the direction of
the arrow and press the trigger (5).
Switching off: Release the trigger (5).
Continuous operation (depending on features)
Switching on:
Slide the lock (4) in the direction of the
arrow, press the trigger (5) and keep it
pressed. The machine is now switched on.
Now slide the lock (4) in the direction of the
arrow once more to lock the trigger (5)
(continuous operation).
Switching off:
Press the trigger (5) and release.
8.2 Working instructions
Grinding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Roughing: position the machine at an angle of 30° -
40° for the best working results.
Separating:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Sanding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Machine with "
X" in the model designation:
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the current supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
- When switched on, the machine accelerates
to maximum speed very quickly, i.e. automatic
restriction of the starting current does not work
(soft start). An electronic error exists. Other
safety-related electronic functions are no longer
available. Have the machine repaired immediately
(see 12.).
W 2000:
- Switching on procedures produce brief reductions
in voltage. Unfavourable power conditions can be
detrimental to other devices. Power impedances
smaller than 0.2 ohm should not cause any
malfunction.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
See page 4.
A Roughing disc (always use with safety guard
attached)
B Louver disc (always use with safety guard
attached)
C Parting safety guard.
D Parting disc (always use with parting safety
guard attached)
E Diamond discs (always use with safety guard or
parting safety guard attached)
F Cup wheel guard (place on machine and secure
with screws (f)). Secure cup wheel as described
in chapter 7.. Use an offset 2-hole spanner if
necessary. Use the wing screws to adjust the
safety guard until the cup wheel protrudes
between 0.5 cm - 1 cm.
G Cup wheels (always use with cup wheel safety
guard attached)
H Offset 2-hole spanner (for
securing/loosening
the clamping nut (8)
on cup wheels)
I Parting safety guard with guide slot (place on
machine and secure with screws.) (with adapter
for connection to a suitable dust extractor for
extraction of stone dust generated when cutting
stone slabs.)
J Hand guard (for attaching under the additional
side-mounted handle.)
K Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx. 35
mm)
L Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
M Fibre discs (always use with the hand guard
attached.)
9. Cleaning
10. Troubleshooting
11. Accessories

Содержание

Похожие устройства

Скачать