Microlife BP 2BHO [10/50] Eel 150
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Microlife BP 2BHO [10/50] Eel 150

Microlife BP 2BHO [10/50] Eel 150
f) Remain seated quietly for 2 minutes before you
begin the measurement.
Comment:
If it is not possible to fit the cuff to the left arm, it can also
be placed on the right one. However all measurements
should be made using the same arm
5.4. Setting the inflation pressure
Program the inflation pressure to be approximately 40 mmHg higher than your estimated systolic blood
pressure. You can choose between 8 initial values: 140, 160, 180, 200, 220, 240, 260 and 280 mmHg. If
you do not know your systolic blood pressure, select a value between 160 and 200. The instrument is pre-
set to 140 mmHg. If this initial value is sufficient for you, omit the following step and start immediately
with the measurement.
Set the initial pressure as follows:
a) Switch on the instrument by pressing the O/I button.
This picture appears on the LCD display. (It remains
there as long as you hold the button pressed down).
b) After the button is released, the display flashes as
shown and the instrument beeps. This indicates that
the instrument is automatically adjusting itself to
the pressure of the surroundings.
c) After this equalization is completed, zero is displayed.
Finally a beep is emitted to indicate that the instru-
ment is ready to take measurements.
d) On pressing the SET button the instrument displays
the pre-set initial pressure for approx. 3 seconds.
e) In order to set the initial pressure individually, press
the SET button briefly for each level until the required
initial pressure is reached. Each button press raises
the initial pressure by 20 mmHg. After reaching
280 mmHg the display starts again at 120 mmHg.
f) After the SET button has been released, the instru-
ment is set to the displayed value and the setting up
procedure is complete. As long as the batteries are
not removed, the value is stored in the instrument
even after it has been switched off.
Comment:
If the initial pressure selected was too low it will be corrected automatically during the measurement by
additional inflation. This results in a slightly longer measuring procedure which the patient may find
uncomfortable. The result of the measurement is normally not affected.
7

Содержание

Похожие устройства

f Remain seated quietly for 2 minutes before you begin the measurement Comment If it is not possible to fit the cuff to the left arm it can also be placed on the right one However all measurements should be made using the same arm 5 4 Setting the inflation pressure Program the inflation pressure to be approximately 40 mmHg higher than your estimated systolic blood pressure You can choose between 8 initial values 140 160 180 200 220 240 260 and 280 mmHg If you do not know your systolic blood pressure select a value between 160 and 200 The instrument is pre set to 140 mmHg If this initial value is sufficient for you omit the following step and start immediately with the measurement Set the initial pressure as follows a Switch on the instrument by pressing the O l button This picture appears on the LCD display It remains there as long as you hold the button pressed down b After the button is released the display flashes as shown and the instrument beeps This indicates that the instrument is automatically adjusting itself to the pressure of the surroundings SYS mmHg____________________ IXAmmHg c After this equalization is completed zero is displayed O Finally a beep is emitted to indicate that the instru ment is ready to take measurements PULS nri d On pressing the SET button the instrument displays SYS mmHg____________________ DfAmmHg the pre set initial pressure for approx 3 seconds e In order to set the initial pressure individually press the SET button briefly for each level until the required 5EL IHO PULSBmr initial pressure is reached Each button press raises the initial pressure by 20 mmHg After reaching 280 mmHg the display starts again at 120 mmHg f After the SET button has been released the instru SYS mmHg____________________ O A mmHg EEL 150 PtAS mn ment is set to the displayed value and the setting up procedure is complete As long as the batteries are not removed the value is stored in the instrument even after it has been switched off SYSm M g______________________ DlA irHg 5EL 180 Comment If the initial pressure selected was too low it will be corrected automatically during the measurement by additional inflation This results in a slightly longer measuring procedure which the patient may find uncomfortable The result of the measurement is normally not affected

Скачать