Binatone TP-4055 [7/34] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Binatone TP-4055 [7/34] English

Binatone TP-4055 [7/34] English
77
77
7
ENGLISHENGLISH
ENGLISHENGLISH
ENGLISH
OPERATING MANUAL
1. Place the appliance on a dry horizontal sur-
face.
2. Open the lid
(3)(3)
(3)(3)
(3) by pulling the lid locking
valve
(4)(4)
(4)(4)
(4) upward.
3. Fill the thermopot with water; in doing so be
careful so that water does not splash onto the
appliance casing and its electrical parts.
Attention: Do not pour water in the thermopot from the
side where the control panel (8) is located. If water
penetrates inside the panel, this could result in failures
in the appliance operation.
4. Make sure that the water level is not above a mark “Full”on the
water level scale
(2)(2)
(2)(2)
(2). Do not turn on the thermopot when empty.
Minimum required amount of water should not be lower than
the lowest mark on the water level scale.
Note: If the water level is lower than the small pipe on the
heating element, the protection system preventing
waterless operation activates and the appliance is
switched off.
5. Push the lid
(3)(3)
(3)(3)
(3) to close it.
6. Connect the detachable power cable
(15)(15)
(15)(15)
(15) and insert the plug
into a socket with a power supply with voltage that should
comply with the data indicated on the appliance.
Attention: Never connect the power cable if hands are wet.
7. When first connecting to a power supply, the indicator “Boil”
will light up and the thermopot will immediately start boiling.
Attention: intensive evaporation may occur for several
minutes during boiling: it is a normal and necessary
to destroy chlorine contained in water
8. Immediately after boiling the thermopot will enter the water
temperature maintenance mode. Indicator “Keep warm” will
light up.
9. To pour water out of the thermopot, press the button “Unlock”
and release the locking mode (presetting). The symbol “Un-
lock” will show that the locking mode is released. Place a cup
under the water supply port
(6)(6)
(6)(6)
(6) and press the button “Dis-
pense”. Release the button when the cup is full. Ten seconds
later the water dispense mode will be set and the indicator
“Unlock” will go out.
10. Water can also be dispensed by using the manual pump
(6)(6)
(6)(6)
(6). Unlock the pump
(6)(6)
(6)(6)
(6) by moving the manual pump lock
lever
(7)(7)
(7)(7)
(7) to “Open”. Place a cup under the water supply port
(6)(6)
(6)(6)
(6) and push the pump button. Release the button when the
cup is filled up. Move the manual pump lock lever
(7)(7)
(7)(7)
(7) to “Lock”.
11.To supply water, the “Cup switch”
(9)(9)
(9)(9)
(9) can be used. Press the
valve with a cup and move the cup away when the required
amount of water is dispensed.

Содержание

Похожие устройства

1 Place the appliance on a dry horizontal sur face 2 Open the lid 3 by pulling the lid locking valve 4 upward 3 Fill the thermopot with water in doing so be careful so that water does not splash onto the appliance casing and its electrical parts Attention Do not pour water in the thermopot from the side where the control panel 8 is located If water penetrates inside the panel this could result in failures in the appliance operation 4 Make sure that the water level is not above a mark Full on the water level scale 2 Do not turn on the thermopot when empty Minimum required amount of water should not be lower than the lowest mark on the water level scale Note If the water level is lower than the small pipe on the heating element the protection system preventing waterless operation activates and the appliance is switched off 5 Push the lid 3 to close it 6 Connect the detachable power cable IS and insert the plug into a socket with a power supply with voltage that should comply with the data indicated on the appliance Attention Never connect the power cable if hands are wet 7 When first connecting to a power supply the indicator Boil will light up and the thermopot will immediately start boiling Attention intensive evaporation may occur for several minutes during boiling it is a normal and necessary to destroy chlorine contained in water 8 Immediately after boiling the thermopot will enter the water temperature maintenance mode Indicator Keep warm will light up 9 To pour water out of the thermopot press the button Unlock and release the locking mode presetting The symbol Un lock will show that the locking mode is released Place a cup under the water supply port 6 and press the button Dis pense Release the button when the cup is full Ten seconds later the water dispense mode will be set and the indicator Unlock will go out 10 Water can also be dispensed by using the manual pump 6 Unlock the pump 6 by moving the manual pump lock lever 7 to Open Place a cup under the water supply port 6 and push the pump button Release the button when the cup is filled up Move the manual pump lock lever 7 to Lock 1 l To supply water the Cup switch 9 can be used Press the valve with a cup and move the cup away when the required amount of water is dispensed ENGLISH OPERATING MANUAL

Скачать