Bomann DBS 783 CB [41/74] Anti scale filter
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bomann DBS 783 CB [41/74] Anti scale filter

Bomann DBS 783 CB [41/74] Anti scale filter
41
CAUTION: Initial use:
4. If the handle is still in the carrying position, release the
lock as described under “Function of the Handle”.
5. Use the selector button SET (11) to set the temperature.
Refer to the table above.
6. Wait until the sole plate has heated up. The operating
temperature is reached as soon as the blue indicator
stops ashing and a beep sounds.
7. Press the steam jet button (1) for at least ½minute. As
an alternative, you can pull back the lock (9) to lock the
steam jet button (10). This time is needed for the steam
to reach the iron. A slightly louder noise of the pump is
normal with this.
NOTE ON STEAM IRONING:
• Setting
is not intended for steam ironing (see table).
• The amount of steam is electronically controlled. It is
based on the ironing temperature.
• The ironing temperature is electronically controlled during
use. The device heats up if the blue indicator on the
display starts ashing slowly.
After use, press the selector button SET (11) repeatedly until
the red control lamp appears in the display. Disconnect the
mains plug from the socket.
Vertical Steam function (Vertical Steam)
This can be used to produce a jet of steam in a vertical direc-
tion. This function can be used to remove creases from hanging
clothes or from curtains.
WARNING:
Never point the steam jet at other people. Danger of burns.
Hang your laundry on a clothes hanger and move the iron to
approximately 5-15 cm away.
How can I replenish the water during operation?
Rell with water before the tank is completely empty. A loud noi-
se of the pump during operation indicates that the water level is
too low.
1. Place the iron on the rest (5).
2. Press the selector button SET (11)
repeatedly until the red control
lamp appears in the display.
3. Remove the mains plug from the
socket.
4. In order to remove the tank, press
the RELEASE button below the
water tank. (Fig. C).
5. Remove the lime lter cartridge
(Fig. D).
6. Fill the tank up to the maximum
mark (Fig. E). Do not overll!
7. Reinsert the lime lter cartridge
and push the tank back into
the base (Fig. F + G). A “click“
conrms that the water tank has
been set correctly.
8. You can now continue ironing.
NOTE:
The tank illumination lights once the mains plug has been
inserted into the outlet. If it does not light, the lime lter
cartridge or the water tank has not been set correctly. Check
both positions.
When you have nished
1. Press the selector button SET (11) repeatedly until the red
control lamp appears in the display. Remove the mains
plug from the socket. The light on the display goes out.
2. Allow the device to cool down before you put it away.
Anti-scale lter
Your steam iron station is tted with an anti-scale lter. The anti-
scale lter cartridge becomes spent after ltering approximately
18 litres of water, depending on the hardness of your water. It
then loses its effectiveness and must be replaced.
1. Turn off the appliance.
2. Disconnect the mains plug from the mains.
3. Remove the water tank.
4. Remove the anti-scale lter cartridge.
5. Fill the tank up to the maximum mark. Do not overll!
6. Insert a new anti-scale lter cartridge.
7. Before turning on the appliance, wait a few minutes until
the new lter cartridge is saturated with water.
NOTE:
If you do not have a new anti-scale lter cartridge, you can
still iron with the used cartridge and distilled water.
Cleaning
WARNING:
• Always remove the mains lead before cleaning!
• Wait until the machine has cooled down completely.
• Under no circumstances should you immerse the device
in water for cleaning purposes. Otherwise this might
result in an electric shock or re.

Содержание

Похожие устройства

Скачать