Bomann BS 968 CB [26/42] Cleaning and storage
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bomann BS 968 CB [26/42] Cleaning and storage

Bomann BS 968 CB [26/42] Cleaning and storage
ENGLISH
ENGLISH
26
Cable winding device
Pull out the cable up to the maximum length indicated with the
yellow mark. Never pull the cable out up to the red mark as the
cable winding can be damaged. Said damages are not covered
by the warranty.
Winding
Press the cable (3) winding button and guide the cable. Hold the
cable to avoid wrapping.
Nozzle Attachment
Crevice and
jointed nozzle:
For vacuuming upholstery, curtains and
in corners and crevices etc.
„2-in-1“ nozzle: When they are joined
together you can use them as a brush
nozzle. If you would like to use the
crevice nozzle, pull the brush section off
Upholstery nozzle: For cleaning upholstery, curtains etc.
Floor nozzle:To clean carpets or smooth surfaces
Releasing the
nozzles:
Pull these off while turning slightly
Air Slide (4)
Open the air slide on the hose handle in order to regulate the
airfl ow or to clear any particles sticking to the nozzle.
Dust bag replacement display (14)
Hold the hose up into air. If the display is red the bag is full.
Please replace it.
Changing the dust bag
• Pull the plug out of the socket.
• Open the lid of the dust bag compartment by the handle (11)
(the cover must click into place).
• Remove the bag by carefully pulling the clamp towards
the front so that the bag becomes more accessible. Then
remove the dust bag by pulling it upwards.
• Insert a new bag. Please ensure that the bag is located
correctly in the guide mechanism. Then reinsert the retainer.
Close the cover so that it snaps into place.
Filter
Your appliance has two fi lters.
Motor protection fi lter (inlet fi lter)
The inlet fi lter is located in the dust bag compartment. The fi lter
is located vertically in the rear section of the dust housing.
• Remove the grille by pulling it upwards and then take out the
motor protection fi lter.
• Clean the engine protection fi lter after 10 dust bag changes.
If necessary, the fi lter can also be washed in warm water
without any additives.
• Place it back into place only once it is completely dry!
• Please push the grille back down into the guide mechanism
so that it is correctly positioned.
Outlet fi lter
The appliance is also equipped with an outlet fi lter. This fi lter is
to be found under the fi lter cover (16).
• Press the lever above the ventila-
tion grille downwards in order to
open it.
• Then pull the grille out towards the
front.
• Remove the fi lter and clean as
described above.
• Please re-insert the fi lter correctly
and close the ventilation grille
(until it clicks in place).
Cleaning and storage
Cleaning
• Pull the plug out of the socket before cleaning!
• Clean the casing with a dry cloth.
Storage
• Let the iron cool down completely.
• Wind the cable completely.
• If you position the device horizontally: Please suspend the
hook of the fl oor nozzle in the parking assistant (15) on the
back of the device.
Troubleshooting
Symptoms Course Solution
The Device Does
Not Work
Check the connec-
tion to the mains
Check the position
of the switch
The device does
not suck up
anything
The suction power
is set too low
Check the position
of the control switch
The dust bag is full Renew the dust
bag
The fi lters are dirty Clean the compo-
nents
There is a foreign
body in the suction
tube or the nozzle
Check the acces-
sories for foreign
bodies
Noise development
The sound pressure level in the ear of an operator (LpA) was
measured according to DIN EN ISO 3744.
Sound pressure level detected: 82.0 dB(A) (no limit)
05-BS 968 CB.indd 2605-BS 968 CB.indd 26 04.02.2008 8:53:49 Uhr04.02.2008 8:53:49 Uhr

Содержание

Похожие устройства

Скачать