![Haier AS182AVERA [6/8] Outdoor unit](/img/pdf.png)
Haier AS182AVERA [6/8] Outdoor unit
![Haier AS182AVERA [6/8] Outdoor unit](/views2/1808064/page6/bg6.png)
Outdoor unit
1.Installation of Outdoor Unit
3.Connection
4.Attaching Drain-Elbow
2.Connection of pipes
Install according to
To bend a pipe, give the roundness as large as possible not to crush the pipe ,and the bending radius
should be 30 to 40 mm or longer.
Connecting the pipe of gas side first makes working easier.
The connection pipe is specialized for R410A.
The max vertical distance between the indoor unit and the outdoor unit is 15 m.
Be careful that matters, such as wastes of sands, etc. shall not enter the pipe.
The standard pipe length is 5m. The better vertical distance between the indoor unit and the outdoor
unit ranges between 2m and 5m. If it is over 5m, the function of the unit will be affected. If the pipe has
to be lengthened, the refrigerant should be charged, according to 30 g/m. But the charge of refrigerant
must be conducted by professional air conditioner engineer. Before adding additional refrigerant,
perform air purging from the refrigerant pipes and indoor unit using a vacuum pump,then charge
additional refrigerant.
Use the same method on indoor unit. Loosen the screws on terminal block and insert the plugs fully into
terminal block, then tighten the screws.
If wiring is not correct, proper operation can not be carried out and controller may be damaged.
If the drain-elbow is used, please attach it as
figure. (Note: Only for heat pump unit.)
Forced fastening without careful centering
may damage the threads and cause a
leakage of gas.
Pipe Diameter ( )
Liquid side 6.35mm(1/4")
Fastening torque
Drawing for the installation of indoor and outdoor units
Insert the cable according to terminal number in the same manner as the indoor unit.
Fix the cable with a clamp.
18N.m
Half union
Flare nut
Spanner
Torque wrench
6
Gas side 12.7mm(1/2")
55N.m
5.Outdoor indicator board
On the top left of outdoor wiring block, you can find an indicator board, which can show out the failure. There
are 5 LEDS on the board, and the different states will shows different failures. In addition, there is also a
4-digit dip switch on the board, please do not change the switch position.
The max pipe length between the indoor unit and the outdoor unit is 30m.
If the fuse of outdoor unit is broken, please change it with the type of T25A/250VAC.
Содержание
- Fix the unit to concrete or block with bolts 10mm and nuts firmly and horizontally when fitting the unit to wall surface roof or rooftop fix a supporter surely with nails or wires in consideration of earthquake and strong wind 2
- Fixing of outdoor unit 2
- If vibration may affect the house fix the unit by attaching a vibration proof mat 2
- Indoor unit 2
- Outdoor unit 2
- Power source 2
- Selection of installation place 2
- Selection of pipe 2
- Carry out based on the neighboring pillars or lintels a proper leveling for the plate to be fixed against the wall then temporarily fasten the plate with one steel nail 2 make sure once more the proper level of the plate by hanging a thread with a weight from the central top of the plate then fasten securely the plate with the attachment steel nail 3 find the wall hole location a using a measuring tape 3
- Drawing of pipe 3
- Fitting of the mounting plate and positioning of the wall hole 3
- Fix to side bar and lintel a mounting bar which is separately sold and then fasten the plate to the fixed mounting bar 3
- Indoor unit 3
- Installation of the indoor unit 3
- Left left rear piping 3
- Making a hole on the wall and fitting the piping hole cover 3
- Rear piping 3
- Refer to the previous article when the mounting plate is first fixed for the position of wall hole 3
- When the mounting plate is first fixed 3
- When the mounting plate is fixed side bar and lintel 3
- Connecting the indoor outdoor electric cable 4
- Fixing the indoor unit body 4
- Indoor unit 4
- Removing the wiring cover 4
- When connecting the cable after installing the indoor unit 4
- When connecting the cable before installing the indoor unit 4
- Easily demount cleaning of indoor unit 5
- Indoor unit 5
- Attaching drain elbow 6
- Be careful that matters such as wastes of sands etc shall not enter the pipe the standard pipe length is 5m the better vertical distance between the indoor unit and the outdoor unit ranges between 2m and 5m if it is over 5m the function of the unit will be affected if the pipe has to be lengthened the refrigerant should be charged according to 30 g m but the charge of refrigerant must be conducted by professional air conditioner engineer before adding additional refrigerant perform air purging from the refrigerant pipes and indoor unit using a vacuum pump then charge additional refrigerant 6
- Connection 6
- Connection of pipes 6
- Installation of outdoor unit 6
- Outdoor indicator board 6
- Outdoor unit 6
- Outdoor unit 7
- Purging method to use vacuum pump 7
- Check for installation and test run 8
- Check items for test run 8
- Correct incorrect 8
- Cutting and flaring work of piping 8
- Flare tooling die 8
- Full disconnection circuit breaker must be installed in fixed wiring 8
- On drainage 8
- Pipe cutting is carried out with a pipe cutter and burs must be removed after inserting the flare nut flaring work is carried out 8
- Please install the drain hose so as to be downward slope without fail please don t do the drainage as shown below 8
- Please kindly explain to our customers how to operate through the instruction manual 8
- Please pour water in the drain pan of the indoor unit and confirm that drainage is carried out surely to outdoor in case that the attached drain hose is in a room please apply heat insulation to it without fail 8
- Power source installation 8
- The power source must be exclusively used for air conditioner over i5a in the case of installing an air conditioner in a moist place please install an earth leakage breaker for fixed wiring installation a contact separation in all poles that provide full disconnection under overvoltage category iii conditions should be installed the disconnection must be incorporated in the fixed wiring in accordance with the wiring rules eg a approved all poles 8
Похожие устройства
- Haier AS182AVERA Сервис мануал
- Haier AS182AVERA Технические данные
- Haier AU36NAHERA Инструкция по монтажу
- Haier AU422AIERA Инструкция по монтажу
- Haier AU42NAIERA Инструкция по монтажу
- Haier AU522AIERA Инструкция по монтажу
- Haier AU52NAIERA Инструкция по монтажу
- Haier AC422AFERA Инструкция по эксплуатации
- Haier AC522AFERA Инструкция по эксплуатации
- Haier AU142AAERA Инструкция по монтажу
- Haier AD09LS1ERA Руководство по эксплуатации
- Haier AD09LS1ERA Сервис мануал
- Haier AD12LS1ERA Руководство по эксплуатации
- Haier AD12LS1ERA Сервис мануал
- Haier AD18LS1ERA Руководство по эксплуатации
- Haier AD24LS1ERA Руководство по эксплуатации
- Haier AD18LS1ERA Сервис мануал
- Haier AC18CS1ERA(S) Сервис мануал
- Haier AC24CS1ERA(S) Сервис мануал
- Haier 3U19FS1ERA Сервис мануал