![Haier HSU-12HQA03/R2(DB) [5/16] When restart after remote turning off the remote memorize the previous](/img/pdf.png)
Haier HSU-12HQA03/R2(DB) [5/16] When restart after remote turning off the remote memorize the previous
![Haier HSU-12HQA03/R2(DB) [5/16] When restart after remote turning off the remote memorize the previous](/views2/1820179/page5/bg5.png)
Operation
AUTO COOL DRY FAN HEAT
2.Select operation mode
Press MODE button. For each press, operation mode
changes as follows:
Remote controller:
1. Unit start
Press ON/OFF on the remote controller, unit starts.
Base Operation
Remote controller
Air Flow Direction Adjustment
Vertical flap
Pos.1
Pos.2
Pos.3
Pos.4
Pos.5
Pos.6
(Auto swing)
1.Status display of air flow
When restart after remote turning off, the remote
memorize the previous
2.Left and right air flow adjustment
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
adjusted to left or
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
Emergency Operation:
temperature is below 16
o
C, do not use it in the
Test operation:
Use this switch in the test operation when the room
normal operation.
your finger from the switch: the cooling
Continue to press the test operation
switch for more than 5 seconds . After
you hear the "Pi" sound twice,
release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
Emergency operation and test operation
Use this ope
r
ation only when the remote controller
is defective or lost.
When the emergency operation switch is
pressed,the" Pi "sound is heard once
, which
the start of this operation.
In this operation, the system automatically selects
the
operation modes
,cooling or fan or heat,
according to the room temperature.
.
It is not possible to operate in dry mode.
Room
temperature
Operation
mode
Designated
temperature
Timer
mode
Air flow
ABOVE 24
O
C
BELOW 24
O
C
COOLING
HEAT
2
4
O
C
2
4
O
C
NO
NO
AUTOMATIC
AUTOMATIC
(C
ooling only uint）
Room temperature
Operation
mode
Designated
temperature
Timer
mode
Air flow
BELOW 2
4
O
C
FAN
2
4
O
C
NO
AUTOMATIC
at air outlet if all vertical louvers are
right.
mode ,
controller will automatically
Note:
set swing position.
means
Operation
Mode
AUTO
Remote
Controller
Note
COOL
DRY
HEAT
FAN
In DRY mode, when room temperature becomes
lower than temp.setting+2
o
C, unit will run
intermittently at LOW speed regardless of FAN
Under the mode of auto operation, air conditioner
will automatically select Cool or Heat operation
according to room temperature. When FAN is set
to AUTO, the air conditioner
automatically adjusts
temperature.
the fan speed according to room
In FAN operation mode , the unit will not operate in
COOL or
HEAT mode but only in
FAN mode ,
AUTO is not available in
FAN mode.
And temp.
setting is disabled. In FAN mode, sleep operation
setting.
is not available.
Pi
emergency
operation
switch
test operation
switch
Pi
Pi
Press FAN button. For each press, fan speed
follows:
Remote controller:
Press button
Every time the button is pressed, temp.setting
increase 1
o
C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1
o
C,if kept depressed, it will
decrease rapidly
Select a desired temperature.
4.Fan speed selection
3.Select temp.setting
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
LOW
MED
HI
AUTO
/
changes as
3
1
4
2
Pos.1
Pos.2
Pos.3
Pos.4
Pos.5
Pos.6
Pos.7
Pos.8
For each press of button, remote controller
displays as follows :
remote controller:
Содержание
- Hsu 12hqa03 r2 db 1
- Operation manual 1
- Please read this operation manual before using the air conditioner 1
- Cautions 3
- Contents 3
- Parts and functions operation maintenance 3
- Trouble shooting 3
- Actual indoop unit may vary from the one shown in the manual according to the product purchased 4
- Air purifying 4
- Clock set 4
- Filter anion generator 4
- Indoor unit 4
- Inlet grille 4
- Light button 4
- Loading of the battery 4
- Nano aquo generator inside 4
- Outdoor unit 4
- Outlet horizontal flap 4
- Parts and functions 4
- Remote controller 4
- Reset button 4
- Vertical blade 4
- Air conditioner is running under displayed fan speed when fan is set to auto the air conditioner automatically adjusts the fan speed according to room temperature 5
- Air flow direction adjustment 5
- Base operation 5
- C if kept depressed it will decrease rapidly select a desired temperature 5
- C if kept depressed it will increase rapidly every time the button is pressed temp setting decrease 5
- Cautions 5
- Changes as 5
- Continue to press the test operation 5
- Controller will automatically 5
- Emergency operation and test operation 5
- For each press of button remote controller displays as follows remote controller 5
- Operation 5
- Operation mode 5
- Operation starts with the air flow speed hi 5
- Pos pos pos 5
- Pos pos pos pos 5
- Press button every time the button is pressed temp setting increase 1 5
- Press fan button for each press fan speed follows remote controller 5
- Press mode button for each press operation mode changes as follows remote controller 5
- Press on off on the remote controller unit starts 5
- Remote controller 5
- Remote controller note 5
- Set swing position 5
- Switch for more than 5 seconds after you hear the pi sound twice 5
- Test operation switch is the same as emergency switch 5
- Use this switch in the test operation when the room 5
- When restart after remote turning off the remote memorize the previous 5
- Your finger from the switch the cooling 5
- In auto mode 6
- In fan mode 6
- In heat mode 6
- Nano aquo operation 6
- Operation 6
- Operation mode 1 in cool dry mode 6
- Power soft operation 6
- Sleep operation 6
- Use of sleep function 6
- Displa 7
- For a minute and then start adjusting by remote controller 7
- Goes on 7
- Operation 7
- Setting the comfort work conditions 7
- Timer on off on off operation healthy airflow operation 7
- Air filter cleaning 8
- Attach air purifying filter 8
- Attach the standard air filter 8
- Attention 8
- Close doors and windows during operation 8
- Close the inlet grille 8
- Detach the standard air filter 8
- Do not block the air inlet or outlet 8
- Do not use the following for cleaning 8
- For smart use of the air conditioner 8
- If the unit is not to be used for a long time turn off the power supply main switch 8
- Maintenance 8
- Open the lnlet grille 8
- Remote controller indoor body 8
- Replacement of air purifying filter 8
- Setting of proper room temperature 8
- Use the louvers effectively 8
- Use the timer effectively 8
- Caution 9
- Cautions 9
- Please call sales service shop for the installation do not attempt to install the air conditioner by yourself because improper works may cause electric shock fire water leakage 9
- Warning 9
- Before asking for service check the following first 10
- Cautions 10
- Specifications 10
- The machine is adaptive in following situation 10
- Trouble shooting 10
- Specifications 11
- B black 12
- Bl blue w white y g yellow green 12
- Br brown 12
- C0n1 bl 12
- Cn21 cn23 12
- Con2 r 12
- Con3 w 12
- Electrical diagram 12
- Between the ipm and cbd 13
- Cn9 cn8 13
- Communication fault 13
- Dc fan motor 13
- Description 13
- Deviate from the normal exhaust temperature sensor failure ambient temperature sensor failure 13
- Don t touch capacitor even after plug off danger of electric shock 13
- Electrical diagram 13
- Exhaust temperature frost removing temperature sensor failure 13
- For the compressor loop of the station detect error overcurrent of the compressor 13
- Main control board 13
- Module board 13
- Of ac electricity 13
- Outdoor eeprom error the protection of ipm 13
- Over pressure or overheat 13
- Overcurrent protection 13
- Overcurrent protection for single phase of the compressor 13
- Overheat protection for 13
- Pfc reactor 13
- Protection for the compressor power voltage is too high or low 13
- The capacitor retains high voltage even after the plug off for your safety be sure to wait at least 5 minutes after plug off and use a tester to confirm the voltage between connector p and n on module board is less than dc 10v before start servicing 13
- To indoor unit 13
- Y g yellow green or orange 13
Похожие устройства
- Haier HW-18LMA03(T3) Инструкция по эксплуатации
- Haier HW-18LMA13(T3) Инструкция по эксплуатации
- Haier HW-24LMA03(T3) Инструкция по эксплуатации
- Haier HW-24LMA13(T3) Инструкция по эксплуатации
- Haier HWF06XC3 Инструкция по эксплуатации
- Haier HPRD12XC7 Инструкция по эксплуатации
- Haier HPRD12XH7 Инструкция по эксплуатации
- Haier HWF05XCL Инструкция по эксплуатации
- Haier HPY08XCM Инструкция по эксплуатации
- Haier HSU-07RK03/R2 Инструкция по эксплуатации
- Haier HSU-12RK03/R2 Инструкция по эксплуатации
- Haier HWE06XCN Сервис мануал
- Haier HWE06XCN Инструкция по эксплуатации
- Haier HWE08XCN Инструкция по эксплуатации
- Haier HWE10XCN Инструкция по эксплуатации
- Haier HWE12XCN Инструкция по эксплуатации
- Haier HWR05XC9 Инструкция по эксплуатации
- Haier HWR05XC9-L Инструкция по эксплуатации
- Haier HWR05XCJ Инструкция по эксплуатации
- Haier HWR05XC5 Сервис мануал