Home
Главная
Stomer
Шуруповерты И Винтоверты
SAD-14x2-D
Инструкция по эксплуатации Страница: 6

Stomer SAD-14x2-D [6/44] English

Cordless drill/driver

INTENDED USE

• This tool is intended for drilling in wood, metal, ceramic

and plastic; tools with electronic speed control and left/right

rotation are also suitable for screwdriving and thread cut-

ting

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 Switch for on/off and speed control

2 Switch for changing direction of rotation

3 Keyless chuck

4 Ring for torque control

5 Switch for selecting mechanical speed

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁ re

and/or serious injury.

• Ensure the switch is in the off position before inserting

battery pack. Inserting the battery pack into power tools

that have the switch on invites accidents.

• Recharge only with the charger speciﬁ ed by the manu-

facturer. A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with another bat-

tery pack.

• Use power tools only with speciﬁ cally designated battery

packs. Use of any other battery packs may create a risk

of injury and ﬁ re.

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the charger (charg-

ers with a rating of 230V or 240V can also be connected

to a 220V supply)

• In case of electrical or mechanical malfunction, imme-

diately switch off the tool or unplug charger from power

source

• SBM Group can assure ﬂ awless functioning of the tool

only when original accessories are used

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• This tool should not be used by people under the age

of 16 years

• Be careful not to drill or drive into areas where electrical

wires may be contacted

• Ensure that switch (2) is in the middle (locking) position

before making any adjustments or changing accessories

as well as when carrying or storing the tool

• Do not touch the contacts in the charger

• Do not expose tool/charger/battery to rain

• Never charge battery outdoors

• Store tool/charger/battery in locations where tempera-

ture will not exceed 40° C or drop below 0° C

• Batteries will explode in ﬁ re, so do not burn battery for

any reason

• When damaged, and under extreme usage and tem-

perature conditions, batteries may start to leak

- if liquid comes into contact with the skin, wash quickly

with soap and water, then with lemon juice or vinegar

- if liquid gets into the eyes, ﬂ ush eyes with clean water

for a minimum of 10 minutes and seek immediately medi-

cal attention

• When battery is not in tool or charger, it should be kept

away from metal objects such as nails, screws, keys etc.

to prevent short-circuit

• Do not use charger when damaged; take it to one of

the ofﬁ cially registered SBM Group Service Stations for

a safety check

• Do not use battery when damaged; it should be re-

placed immediately

• Do not disassemble charger or battery

• Do not attempt to recharge non-rechargeable batteries

with the charger

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live)

wire in the cord of the charger to the earth terminal of

the plug

• If for any reason the old plug is cut off the cord of the

charger, it must be disposed of safely and not left unat-

tended

To ensure longer service life and proper per-

formance of the battery, take the following ac-

tions when you start using new battery:

1. Use the new battery, without recharging it, till its com-

plete discharge.

2. Then charge the battery for 1 hour.

3. Repeat abovementioned actions (1 and 2) 3-5 times to

reach the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots free

from dust and dirt.If the dirt does not come off use a soft

cloth moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc. These sol-

vents may damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please con-

tact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of the

packaging materials can be recycled. Take these materi-

als to the appropriate recycling locations. Take your un-

wanted machines to your local SBM Group dealer. Here

they will be disposed of in an environmentally safe way.

NiCd batteries can be recycled. Deliver them to a disposal

site for chemical waste so that they can be recycled or dis-

posed of in an environmentally friendly manner.

English

Stomer SAD-14x2-D [6/44] English

Содержание

Похожие устройства