DWT HLP20-600 K 5.1.59 Инструкция по эксплуатации онлайн [11/64] 662302
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

DWT HLP20-600 K 5.1.59 Инструкция по эксплуатации онлайн [11/64] 662302

DWT HLP20-600 K 5.1.59 Инструкция по эксплуатации онлайн [11/64] 662302
11
English
The manufacturer reserves the possibility to introduce changes.
• Deector nozzle 10 is used for treating one surface
and protecting the other (the heating of which is
undesirable, e.g. window glass).
• Reector nozzle 11 is used for changing the air ow
direction.
• Point nozzle 12 is for treating small-area surfaces as
well as for soldering.
General recommendations
• If necessary, put an appropriate special nozzle on
gun nozzle 1.
• Prepare accessories required for work performance
(scraper, palette knife, brush, etc.).
• Switch on the power tool, adjust the air ow and
temperature as described above.
• After the operation completion, place on / off switch 5
in position "1" and let the power tool run for a while so
that it cools down, and only after that you can switch it
off (only for HLP20-600 K model).
Special recommendations for performing different
types of work (see g. 4-6)
Paint and coatings removal (see g. 4.1) - install
at nozzle 9, heat the surface area until the coat-
ing softens, and remove it with a palette knife or
scraper 8.
Lacquer and paint coatings removal from
window frames (see fig. 4.2) - install deflector
nozzle 10 correctly (to protect the glass), heat the
surface area until the coating softens, and remove it
with a palette knife or scraper 8.
Forming plastic pipes (see g. 5.1) - install reector
nozzle 11. Fill the plastic pipe with sand and close it
at both ends to prevent pipe collapse. While moving
the pipe in the hot air ow, heat it and mould it as
required.
Thawing water pipes (see g. 5.2) - install reector
nozzle 11. While moving the power tool, heat a frozen
area from the edge to the middle. While heating plastic
pipes, be careful not to overheat them.
Soldering (see g. 6) - install point nozzle 12. Apply
solder paste on the soldering area. Depending on the
material, heat the soldering area for 50-120 seconds,
and then apply solder alloy. The solder alloy must melt
under the workpiece temperature.
Power tool maintenance /
preventive measures
Before carrying out any works on the power tool it
must be disconnected from the mains.
Taking care of accessories
Keep special nozzles and scraper 8 clean - remove all
materials stuck to them. Regularly sharpen the blade
of scraper 8 - this will facilitate the work and improve
its results.
Cleaning of the power tool
An indispensable condition for a safe long-term
exploitation of the power tool is to keep it clean.
Regularly ush the power tool with compressed air
thought the ventilation slots 4.
After-sales Service and Application Service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts. Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.dwt-pt.com.
•
Transportation
of the power tools
Categorically not to drop any mechanical impact on
the packaging during transport.
• When unloading / loading is not allowed to use
any kind of technology that works on the principle of
clamping packaging.
Environmental
protection
Recycle raw materials instead of
disposing as waste.
Power tool, accessories and packaging should be
sorted for environment-friendly recycling.
The plastic components are labelled for categorized
recycling.
These instructions are printed on recycled paper
manufactured without chlorine.

Содержание

Похожие устройства

Скачать