Candy CDB 475 DN-07 [49/56] Chapter 15

Candy CDB 475 DN-07 [49/56] Chapter 15
Advisory note
During drying phase the drum will accelerate to a higher speed to distribute the load and to
optimize the drying performance
CHAPTER 15
EN
FAULT
If the fault should persist, contact a Candy Technical Assistance Centre. For prompt servicing, give the model of
the washing machine, to be found on the label placed on the cabinet inside of the porthole or on the
guarantee certificate.
Important
1 The use of environment friendly detersives without phosphates may produce the following effects:
- The discharge rinse water may result cloudier due to the presence of zeolites in suspension. This does not
compromise the efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not
remain incorporated in the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing.
- The non-ionic surface-active agents present in the composition of washing machine detersives are often
difficult to remove from the washing itself and, even in small quantities, may produce visible signs of the
formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2 If your washing machine fails to function, carry out the above-mentioned checks before calling the Candy
Technical Assistance Service.
1. Does not function
on any
programme
2. Does not load
water
3. Does not
discharge water
4. Water on floor
around washing
machine
5. Does not spin
6. Strong vibrations
during spin
7. Display reads error
0, 1, 5, 7, 8, 9
8. Display reads
error 2
9. Display reads
error 3
10.Display reads
error 4
Mains plug not plugged in
Mains switch not on
No power
Electric circuit fuses failure
Load door open
See cause 1
Inlet tap turned off
Timer not set correctly
Discharge tube bent
Odd material blocking filter
Leak from the washer between the tap
and inlet tube
The washing machine has not
discharged water
“No spin” setting (some models only)
Washing machine not perfectly level
Transport bracket not removed
Washing load not evenly distributed
No water fill.
No pump out.
Machine overfilled with water.
Insert plug
Turn on mains switch
Check
Check
Close load door
Check
Turn on water inlet tap
Set timer on correct position
Straighten discharge tube
Check filter
Replace washer and tighten the tube
on the tap
Wait a few minutes until the machine
discharges water
Turn the programme dial onto spin
setting
Adjust special feet
Remove transport bracket
Distribute the washing evenly
Call service.
Check water supplies are on.
Check drain is clear.
Check drain hose is not kinked.
Turn off water supply to machine.
Call service.
CAUSE
REMEDY
49

Содержание

CHAPTER 15 FAULT 1 Does not function on any programme 2 Does not load water 3 Does not discharge water REMEDY CAUSE Mains plug not plugged in Insert plug Mains switch not on Turn on mains switch No power Check Electric circuit fuses failure Check Load door open Close load door See cause 1 Check Inlet tap turned off Turn on water inlot tap Timer not set correctly Set timer on correct position Discharge tube bent Straighten discharge tube Odd material blocking filter Check filter 4 Water on floor around washing machine Leak from the washer between the tap and inlet tube Replace washer and tighten the tube on the tap 5 Does not spin The washing machine has not dischargecfwater Wait a few minutes until the machine discharges water No spin setting some models only Turn the programme dial onto spin setting Washing machine not perfectly level Adjust special feet Transport bracket not removed Remove transport bracket Washing load not evenly distributed Distribute the washing evenly 6 Strong vibrations during spin 7 Display reads error 0 1 5 7 8 9 Call service 8 Display reads error 2 No water fill Check water supplies are on 9 Display reads error 3 No pump out Check drain is clear Check drain hose is not kinked 10 Display reads error 4 Machine overfilled with water Turn off water supply to machine Call service Advisory note During drying phase the drum will accelerate to a higher speed to distribute the load and to optimize the drying performance If the fault should persist contact a Candy Technical Assistance Centre For prompt servicing give the model of the washing machine to be found on the label placed on the cabinet inside of the porthole or on the guarantee certificate Important 1 The use of environment friendly detersives without phosphates may produce the following effects The discharge rinse water may result cloudier due to the presence of zeolites in suspension This does not compromise the efficiency of the rinses The presence of white powder zeolites on the washing at the end of the washing cycle This does not remain incorporated in the fabric and does not alter the colour The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing The non ionic surface active agents present in the composition of washing machine detersives are often difficult to remove from the washing itself and even in small quantities may produce visible signs of the formation of foam Carrying out further rinses in cases such as this is not useful 2 If your washing machine fails to function carry out the above mentioned checks before colling the Candy Technical Assistance Service 49

Скачать
Случайные обсуждения