Makita DUM604SYX (196787) [16/84] Installing or removing shear blades for hedge trimmer

Makita DUM604SYX (196787) [16/84] Installing or removing shear blades for hedge trimmer
16 ENGLISH
Installing or removing the shear
blades for grass shear
Removing the shear blades
1. Remove the grass receiver and place the tool
upside down.
►Fig.11
2. While pressing the lock lever, turn the undercover
counterclockwise until
on the undercover is aligned
with on the lock lever.
►Fig.12
3. Removetheundercover,shearblades,andcrank.
►Fig.13: 1.Undercover2.Shearblades3. Crank
Installing the shear blades
1. Preparethecrank,undercover,andnewshear
blades.
►Fig.14: 1. Crank 2.Undercover3.Shearblades
2. Removethebladecoverfromtheoldshear
blades,andthenattachittothenewones.
►Fig.15
3. Adjustthethreepinssothattheyarelinedupon
the alignment line.
►Fig.16: 1.Alignmentline
4. Applyasmallamountofgreasetotheperiphery
ofthecrank.Attachthecranktothepinswiththesmall
andlargeroundsfacingup.
►Fig.17: 1. Crank
5.
Adjustthebladesandbaseplatesothattheholeinthe
baseplateandthetwoprotrusionsonthebladesarelinedup.
►Fig.18
6. Turntheshearbladesupsidedownandinstall
themsothatthepinsonthetooltintheholeonthe
baseplate.Makesurethattheshearbladesarexed
securely in place.
►Fig.19
7. Placetheundercoversothat
on the under-
cover is aligned with on the lock lever.
►Fig.20
8. While pressing the undercover, turn the under-
cover clockwise until
on the undercover is aligned
with on the lock lever.
►Fig.21
9. Makesurethatthelocklevertsinthegrooveon
the undercover.
►Fig.22: 1. Lock lever
CAUTION: Never use the tool without install-
ing the undercover.
10. Removethebladecover,andthenturnonthetool
to check that it works properly.
NOTICE: If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing shear blades
for hedge trimmer
Optional accessory
CAUTION: Attach the blade cover before
removing or installing the shear blades.
Removing shear blades
1. Placethetoolupsidedown.
►Fig.23
2. While pressing the lock lever, turn the undercover
counterclockwise until
on the undercover is aligned
with on the lock lever.
►Fig.24
3. Remove the undercover.
►Fig.25
4. Loosen two screws with a screwdriver and remove
theshearblades.
►Fig.26: 1. Screws
NOTE:Theshearbladescanberemovedwithout
removing the screws.
5. Removethecrankfromtheshearblades.
►Fig.27: 1. Crank
NOTE:Thecrankmayremaininthetool.
NOTE:Attachthebladecoverandthestoragecase
totheremovedshearblades,andthenstorethe
blades.
Installing shear blades
1. Preparethecrank,undercover,andnewshear
blades.
►Fig.28: 1. Crank 2.Undercover3.Shearblades
2. Attachthebladecovertotheshearblades.
►Fig.29
3. Adjustthethreepinssothattheyarelinedupon
the alignment line.
►Fig.30: 1.Alignmentline
4. Applyasmallamountofgreasetotheperipheryof
thecrank.Attachthecranktothepinswithitssmalland
largeroundsfacingdown.
►Fig.31: 1. Crank
5. Slidetheshearbladessothattheholeonthe
baseplateispositionedatthecenteroftheringsof
blades.
►Fig.32
6. Turntheshearbladesupsidedownandinstall
themsothatthepinonthetooltsintheholeonthe
shearblades.Inserttheclawofthebaseplateintothe
grooveonthetool.Makesurethattheshearbladesare
xedsecurelyinplace.
►Fig.33: 1. Claw
7. Tightenthetwoscrewsrmlywithascrewdriver.
►Fig.34: 1. Screws

Содержание

Похожие устройства

Скачать