Makita Пила торцовочная LH1040F комбинированная +Отвертка аккумуляторная 6723DW [19/60] Push block fig 44

Makita LH 1040 F [19/60] Push block fig 44

CUTTING AS TABLE SAW (BENCH MODE)

CAUTION:

• When using the tool in the table saw mode (bench

mode), place the blade cover on the turn table so that

the blade cover is centered over the slit for the blade

entrance in the turn table and two small bosses on the

underside of the blade cover fit into the semi-circular

slit in the periphery of the turn table as shown in the fig-

ure and then lock the handle in the lowest position by

fully pushing in the stopper pin. (Fig. 43)

• Always use “work helpers” such as push sticks and

push blocks when there is a danger that your hands or

fingers will come close to the blade.

• NEVER withdraw the workpiece while the blade is run-

ning. If you must withdraw the workpiece before com-

pleting a cut, first switch the tool off while holding the

workpiece firmly. Wait until the blade has come to a

complete stop before withdrawing the workpiece. Fail-

ure to do so may cause dangerous kickbacks.

• NEVER remove cut-off material while the blade is run-

ning.

• NEVER place your hands or fingers in the path of the

saw blade.

• Always secure the rip fence firmly, or dangerous kick-

backs may occur.

Work helpers

Push sticks, push blocks or auxiliary fence are types of

“work helpers”. Use them to make safe, sure cuts without

the need for the operator to contact the blade with any

part of the body.

Push block (Fig. 44)

Use a 15 mm piece of plywood.

Handle should be in center of plywood piece. Fasten with

glue and wood screws as shown. Small piece 10 mm x

9 mm x 30 mm of wood must always be glued to plywood

to keep the blade from dulling if the operator cuts into

push block by mistake. (Never use nails in push block.)

Auxiliary fence (Fig. 45 & 46)

Make auxiliary fence from 10 mm and 15 mm plywood

pieces.

Remove the rip fence, clamping screw (A), flat washer

and square nut from the rip fence holder and then attach

and secure the auxiliary fence to the rip fence holder by

using a bolt M6 longer than M6 x 50, washers and nut.

Ripping

CAUTION:

• When cutting long or large workpieces, always provide

adequate support behind the table. DO NOT allow a

long board to move or shift on the table. This will cause

the blade to bind and increase the possibility of kick-

back and personal injury. The support should be at the

same height as the table.

1. Adjust the depth of cut a bit higher than the thick-

ness of the workpiece. To make this adjustment,

loosen two levers and lower or raise the top table.

2. Position the rip fence to the desired width of rip and

secure in place by tightening the clamping screw

(A). Before ripping, make sure the two screws of the

rip fence holder are secured. If it is not secured

enough, retighten it.

3. Turn the tool on and gently feed the workpiece into

the blade along with the rip fence.

(1) When the width of rip is 40 mm or wider, use a

push stick. (Fig. 47)

(2) When the width of rip is narrower than 40 mm,

the push stick cannot be used because the

push stick will strike the top blade guard. Use

the auxiliary fence and push block.

Install securely the auxiliary fence which is

secured to the rip fence holder on the table.

Feed the workpiece by hand until the end is

about 25 mm from the front edge of the top

table. Continue to feed using the push block on

the top of the auxiliary fence until the cut is

complete. (Fig. 48)

Carrying tool

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at left miter angle fully.

Lower the handle fully and lock it in the lowered position

by fully pushing in the stopper pin. (Fig. 49)

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily. (Fig. 50)

CAUTION:

• Always secure all moving portions before carrying the

tool.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

WARNING:

• Always be sure that the blade is sharp and clean for the

best and safest performance.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle

Loosen the grip which secures the turn base. Turn the

turn base so that the pointer points to 0° on the miter

scale. Tighten the grip and loosen the hex bolts securing

the guide fence using the socket wrench. (Fig. 51)

Lower the handle fully and lock it in the lowered position

by pushing in the stopper pin. Square the side of the

blade with the face of the guide fence using a triangular

rule, try-square, etc. Then securely tighten the hex bolts

on the guide fence in the order from the right side.

(Fig. 52)

2. Bevel angle

(1) 0° bevel angle

Lower the handle fully and lock it in the lowered posi-

tion by pushing in the stopper pin. Loosen the lever

at the rear of the tool. Turn the 0° bevel angle adjust-

ing bolt on the right side of the turn base two or three

revolutions clockwise to tilt the blade to the right.

(Fig. 53)

Carefully square the side of the blade with the top

surface of the turn base using the triangular rule, try-

square, etc. by turning the 0° bevel angle adjusting

bolt counterclockwise. (Fig. 54)

Make sure that the pointer on the turn base point to

0° on the bevel scale on the arm. If it does not point

to 0°, loosen the screw which secures the pointer

and adjust the pointer so that it will point to 0°.

(Fig. 55)

Makita Пила торцовочная LH1040F комбинированная +Отвертка аккумуляторная 6723DW [19/60] Push block fig 44

Содержание

Похожие устройства