Bosch УШМ (болгарка) GWS 18V-10 SC (06019G340D) +Фонарь GLI 18V-300 (06014A1100) [32/473] Connectivity functions

Bosch GWS 18V-10 C (06019G310D) [32/473] Connectivity functions

32 | English

1 609 92A 4B1 | (09.05.2018) Bosch Power Tools

Overload protection indic-

ator (36)

Meaning/cause Solution

Yellow Critical temperature has been reached (mo-

tor, electronics, battery)

Run the power tool at no load and allow it to

cool down

Red Power tool is overheated and will switch off Leave the power tool to cool down

Power tool status indicator

(35)

Meaning/cause Solution

Green Status OK –

Yellow Critical temperature has been reached or bat-

tery is almost empty

Run the power tool at no load and allow it to

cool down, or replace or charge the battery

soon

Illuminated red Power tool is overheated or battery is empty Allow the power tool to cool down, or replace

or charge the battery

Flashing red Kickback shutdown, restart protection or im-

pact shutdown has been triggered

Turn the power tool off and on again

Flashing blue Power tool is connected to a mobile device or

settings are being transferred

–

Connectivity functions

In conjunction with the GCY 30-4 Bluetooth

Low Energy

Module, the following connectivity functions are available for

the power tool:

– Registration and personalisation

– Status check, output of warning messages

– General information and settings

– Management

Read the corresponding operating instructions for informa-

tion about the GCY30-4 Bluetooth

Low Energy Module.

Practical advice

u With the GCY 30-4 Bluetooth

Low Energy Module, the

power tool is equipped with a radio interface. Local

operating restrictions, e.g. in aircraft or hospitals,

must be observed.

u Exercise caution when cutting slots in structural walls;

see the "Information on structures" section.

u Clamp the workpiece if it is not secure under its own

weight.

u Do not load the power tool so heavily that it comes to a

stop.

u If the power tool has been subjected to a heavy load,

continue to run it at no-load for several minutes to

cool down the accessory.

u Do not use the power tool with a cut-off stand.

u Do not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

If the power tool becomes electrostatically charged, the

built-in electronics will switch the power tool off. Press the

on/off switch (6) again to restart the power tool.

Rough grinding

u Never use cutting discs for rough grinding.

The best rough grinding results are achieved with a set angle

of 30° to 40°. Move the power tool back and forth with mod-

erate pressure. This will ensure that the workpiece does not

become too hot or discolour and that grooves are not

formed.

Flap disc

The flap disc (accessory) enables you to machine curved

surfaces and profiles.

Flap discs have a considerably longer service life, lower

noise levels and lower sanding temperatures than conven-

tional grinding discs.

Cutting metal

u Always use the protective guard for cutting (16) when

cutting bonded abrasives.

When carrying out abrasive cutting, use a moderate feed

that is suited to the material being machined. Do not exert

pressure on the cutting disc and do not tilt or swing the

power tool.

Do not attempt to reduce the speed of a cutting disc coming

to a stop by applying pressure from the side.

The power tool must always

work in an up-grinding mo-

tion. Otherwise there is a

risk that it will be pushed

uncontrolled out of the cut.

For best results when cut-

ting profiles and rectangular

tubing, start at the smallest

cross section.

Cutting Stone (see figure

u Provide sufficient dust extraction when cutting stone.

u Wear a dust mask.

Bosch УШМ (болгарка) GWS 18V-10 SC (06019G340D) +Фонарь GLI 18V-300 (06014A1100) [32/473] Connectivity functions

Содержание

Похожие устройства