Главная
Skipped breadcrumb items
DSD180Z без акк. и з.у
Инструкция по эксплуатации Страница: 8

Главная
Makita
DSD180Z без акк. и з.у
Инструкция по эксплуатации Страница: 8

Makita DSD180Z без акк. и з.у — инструкция по безопасному использованию инструмента с аккумулятором [8/48]

Превью страниц Страница 8 / 48

Makita DSD180Z без акк. и з.у [8/48] Caution

8 ENGLISH

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

Thetriggercanbelockedofftopreventitfrombeing

pulledaccidentally.Tolockthetriggeroff,pressthe

button from the side with

marking.Tounlock,press

the button from the side with marking.

►Fig.6: 1. Lock-off button

CAUTION: Always lock the tool off when

carrying or suspending the operation.

Adjusting depth of cut

Thecuttingdepthcorrespondswiththescaleonthe

blade. Loosen the screw on the blade holder until the

bladecanmovefreely.Alignthescaleonthebladewith

thebottomlineofthebladeholder.Thentightenthe

screws.

►Fig.7: 1. Cutting depth 2. Bottom line of the blade

holder 3. Scale on the blade

Themaximumcuttingdepthdependsonthetypeof

thesawblade.Alwaysusethesawbladedesignedfor

cutting the working material.

Type of saw blade Max. cutting depth

For drywall 30 mm

For wood 15 mm

LED light

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keeps on lighting while the switch trigger is being pulled.

Thelampgoesoutapproximately10secondsafter

releasing the trigger.

►Fig.8: 1. Lamp

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Removing the dust collector

CAUTION: Never operate the tool without the

dust collector. Dust may come into your eyes and

causeeyeinjury.

Toremovethedustcollector,holdthetoolhandleand

pull back the tabs on the tool. Be sure to pull the tabs on

the both sides at the same time.

►Fig.9: 1.Tab

When installing, align the dust collector's edge with the

groove on the base.

►Fig.10: 1. Groove

Replacing drywall saw blade

CAUTION: Always clean out all chips or for-

eign matter adhering to the blade and/or blade

holder.Failuretodosomaycauseinsufcienttight-

ening of the blade, resulting in a serious personal

injury.

CAUTION: Do not touch the blade or the

workpiece immediately after operation.Theymay

be extremely hot and could burn your skin.

CAUTION: Make sure that the blade is prop-

erly secured. Insufcienttighteningoftheblademay

causebladebreakageorseriouspersonalinjury.

1. Remove the dust collector.

2. Remove the bolts on the blade holder with the hex

wrench.

►Fig.11: 1. Bolts 2. Blade holder 3. Blade

3. Setanewbladeasshowninthegure.Makesure

that the curved edge of the blade points forward. Fit the

protrusion of the blade holder into the slot on the blade.

►Fig.12: 1. Slot 2.Protrudedportion(oppositeside)

4. Adjustthecuttingdepththentightenthebolts.

5. Attachthedustcollector.

Installing snap-off blade

CAUTION: Always use the snap-off blade with

designated length, width, and thickness.Aninap-

propriatelyinstalledsnap-offbladecanbebroken.A

brokenbladecanyoffandcauseapersonalinjury.

Asnap-offbladecanalsobeusedwiththistool.Use3

segments of 18 mm wide snap-off blade with 0.5 mm

thickness.Themaximumcuttingdepthis12.5mm

when cutting a drywall.

►Fig.13: 1.Threesegmentsofsnap-offblade

1. Loosentheboltsonthebladeholder.Turnthe

blade holder so that its protrusion faces outward.

2. Insertthesnap-offbladesothatthesharpedge

faces forward.

3. Secure the snap-off blade at the position where

theendoftherstsegmentcomestotheedgeofblade

holder as illustrated.

►Fig.14: 1. Blade holder 2.Endoftherstsegment

of snap-off blade 3.Allowablecuttinglength

Attaching blade cap

CAUTION: Always attach the blade cap when

tool is not used.Abareblademaycausepersonal

injuryordamagetothebladeitself.

Makita DSD180Z без акк. и з.у — инструкция по безопасному использованию инструмента с аккумулятором [8/48]

Содержание

Похожие устройства