![Graco Reactor E-10 P29571 [10/68] Isocyanate conditions](/img/pdf.png)
Graco Reactor E-10 P29571 [10/68] Isocyanate conditions
![Graco Reactor E-10 P29571 [10/68] Isocyanate conditions](/views2/1899734/page10/bga.png)
Important Isocyanate (ISO) Information
10 311075ZAD
Important Isocyanate (ISO) Information
Isocyanates (ISO) are catalysts used in two component materials.
Isocyanate Conditions
Spraying or dispensing fluids that contain isocyanates creates potentially harmful mists, vapors, and atomized
particulates.
• Read and understand the fluid manufacturer’s warnings and Safety Data Sheets (SDSs) to know specific
hazards and precautions related to isocyanates.
• Use of isocyanates involves potentially hazardous procedures. Do not spray with this equipment unless you
are trained, qualified, and have read and understood the information in this manual and in the fluid
manufacturer’s application instructions and SDSs.
• Use of incorrectly maintained or mis-adjusted equipment may result in improperly cured material, which could
cause off gassing and offensive odors. Equipment must be carefully maintained and adjusted according to
instructions in the manual.
• To prevent inhalation of isocyanate mists, vapors and atomized particulates, everyone in the work area must
wear appropriate respiratory protection. Always wear a properly fitting respirator, which may include a
supplied-air respirator. Ventilate the work area according to instructions in the fluid manufacturer’s SDSs.
• Avoid all skin contact with isocyanates. Everyone in the work area must wear chemically impermeable
gloves, protective clothing and foot coverings as recommended by the fluid manufacturer and local regulatory
authority. Follow all fluid manufacturer recommendations, including those regarding handling of
contaminated clothing. After spraying, wash hands and face before eating or drinking.
• Hazard from exposure to isocyanates continues after spraying. Anyone without appropriate personal
protective equipment must stay out of the work area during application and after application for the time
period specified by the fluid manufacturer. Generally this time period is at least 24 hours.
• Warn others who may enter work area of hazard from exposure to isocyanates. Follow the recommendations
of the fluid manufacturer and local regulatory authority. Posting a placard such as the following outside the
work area is recommended:
TOXIC FUMES
HAZARD
DO NOT ENTER DURING
SPRAY FOAM APPLICATION
OR FOR ___ HOURS AFTER
APPLICATION IS COMPLETE
DO NOT ENTER UNTIL:
DATE:
TIME:
____________
____________
Содержание
- For spraying or dispensing 1 1 mix ratio materials including epoxies polyurethane foam polyurea coatings and joint fill materials for professional use only not approved for use in european explosive atmosphere locations 1
- Instructions 1
- Contents 2
- Related manuals 3
- Systems 3
- Models 5
- Warning 6
- Warnings 6
- Warning 7
- Warning 8
- Warning 9
- Important isocyanate iso information 10
- Isocyanate conditions 10
- Changing materials 11
- Foam resins with 245 fa blowing agents 11
- Keep components a and b separate 11
- Material self ignition 11
- Moisture sensitivity of isocyanates 11
- Fast recirculation 12
- Overview 12
- Pressure adjust 12
- Slow recirculation 12
- Component identification 13
- Controls and indicators 15
- Heater power switch circuit breaker hp 15
- Motor power switch circuit breaker mp 15
- Motor pump control function knob 15
- Status indicator st 15
- Fluid temperature sensors and displays 16
- Heater temperature controls hc 16
- Connect to a power source 17
- Grounding 17
- Installation 17
- Location 17
- Connect the air hoses 19
- Connect the fluid hoses 19
- Connect the main air supply 19
- Flush before first use 19
- Fill the fluid tanks 20
- Fill the wet cups 20
- Purge air and flush the fluid lines 21
- Operation 22
- Pressure relief procedure 22
- Startup of heated units 22
- Fast recirculation 23
- Heat management tips 23
- Heatup guidelines 23
- Slow recirculation 23
- At cool ambient temperature below 75 f 24 c 24
- At high ambient temperature above 75 f 24 c 24
- Heating foam resins with 245 fa blowing agents 24
- Spraying dispensing 25
- Pause heated units 26
- Refill the tanks 26
- Shutdown 26
- Maintenance 27
- Flushing 28
- Purge the gun hoses nonheated units only 29
- Status code 1 and 2 settings 30
- Status code 1 pressure imbalance 30
- Status code 2 pressure deviation from setpoint 30
- Status codes 30
- Troubleshooting 30
- Status code 3 transducer a failure 31
- Status code 4 transducer b failure 31
- Status code 5 excessive current draw 31
- Status code 6 high motor temperature 31
- Status code 7 no cycle counter switch input 31
- Troubleshooting chart 32
- Before beginning repair 36
- Remove supply tanks 36
- Repair 36
- Recirculation spray valves 37
- Displacement pump 38
- Remove the intake valve 38
- Remove the pump assembly 38
- Calibrate temperature displays 39
- Change display temperature units f c 39
- Control module 39
- Replace temperature display and sensor heated units only 39
- Replace function knob potentiometer 40
- Control board 41
- 311075zad 42
- Control board 249434 120 v 249432 240 v 42
- Control module wiring connections 42
- Cycle counter 42
- Function knob 42
- Heated models only 42
- Heater a 42
- Heater b 42
- J11 120 v board j4 240 v board 42
- J15 j14 j3 j8 42
- Pressure transducer a 42
- Pressure transducer b 42
- Repair 42
- Status indicator 42
- Sw2 see page 29 to adjust settings 42
- Temperature sensor b temperature sensor a 42
- Fluid heaters if supplied 43
- Pressure transducers 43
- Drive housing 44
- Installation 44
- Removal 44
- Cycle counter switch replacement 45
- Electric motor 46
- Installation 46
- Motor brushes 46
- Removal 46
- Test motor 46
- Part ap9570 or cs9570 120 v 15 a heated package part ap9571 or cs9571 240 v 10 a heated package part ap9572 or cs9572 240 v 20 a heated package 48
- Part 249806 120 v 15 a nonheated package md2 part 249808 240 v 10 a nonheated package md2 part 24r984 120 v 15 a nonheated package 2k dispense part 24r985 240 v 10 a nonheated package 2k dispense 49
- Part 25c350 240 v 20 a oem package 50
- Part 249570 120 v 15 a heated proportioner part 249571 240 v 10 a heated proportioner part 249572 240 v 20 a heated proportioner 51
- Heated proportioners 52
- Part 287655 120 v bare proportioner part 287656 240 v bare proportioner 54
- Part 25c350 240 v 20 a oem proportioner 55
- Oem proportioner 56
- Part 249576 120 v nonheated proportioner part 249577 240 v nonheated proportioner 57
- Nonheated proportioners 58
- Part 24l004 120 v heated display part 24l005 240 v heated display 60
- Part 249537 120 v nonheated display part 249538 240 v nonheated display 61
- Part 24l009 recirculation manifold heated models 62
- Part 287755 recirculation manifold nonheated models 62
- Part 249582 cart 63
- Accessories 64
- All units heated units only 64
- Suggested spare replacement parts 64
- All models 65
- Dimensions 65
- Reactor e 10 plural component sprayer 66
- Technical specifications 66
- California proposition 65 67
- California residents 67
- Reactor e 10 plural component sprayer 67
- Warning cancer and reproductive harm www p65warnings ca gov 67
- For the latest information about graco products visit www graco com for patent information see www graco com patents to place an order contact your graco distributor or call to identify the nearest distributor phone 612 623 6921 or toll free 1 800 328 0211 fax 612 378 3505 68
- Graco headquarters minneapolis international offices belgium china japan korea 68
- Graco inc and subsidiaries p o box 1441 minneapolis mn 55440 1441 usa copyright 2020 graco inc all graco manufacturing locations are registered to iso 9001 68
- Graco information 68
- Graco standard warranty 68
- June 2020 68
- Www graco com revision 68
Похожие устройства
- Graco Reactor E-10 P29571 Брошюра
- Graco Reactor E-10 P29571 Сертификат
- Graco Reactor E-10 P29571 Техническая документация
- Graco Reactor E-10 P29572 Инструкция по эксплуатации
- Graco Reactor E-10 P29572 Брошюра
- Graco Reactor E-10 P29572 Сертификат
- Graco Reactor E-10 P29572 Техническая документация
- Graco REACTOR A-25 262572 Инструкция по эксплуатации
- Graco REACTOR A-25 262572 Брошюра
- Graco REACTOR A-25 262572 Сертификат
- Graco REACTOR A-25 262572 Техническая документация
- Graco REACTOR A-25 262614 Инструкция по эксплуатации
- Graco REACTOR A-25 262614 Брошюра
- Graco REACTOR A-25 262614 Сертификат
- Graco REACTOR A-25 262614 Техническая документация
- Graco REACTOR A-25 AP2572 Инструкция по эксплуатации
- Graco REACTOR A-25 AP2572 Брошюра
- Graco REACTOR A-25 AP2572 Сертификат
- Graco REACTOR A-25 AP2572 Техническая документация
- Graco REACTOR A-25 AP2614 Инструкция по эксплуатации