Sony TRINITRON KV-SW292M91K [25/53] Troubleshooting

Sony TRINITRON KV-SW292M91K [25/53] Troubleshooting
25
Additional Information
Sony KV-SW292M91K Group Q17 (GB, RU) _2-657-522-11 (1)
x Troubleshooting
If you find any problem while viewing your TV, you can either use the “Factory
Settings” function or check the Troubleshooting guide below. If the problem
persists, contact your Sony dealer.
“Factory Settings” function
Press the WEGA GATE button. Choose “Settings” and go to “Setup” ( ) menu.
From “Setup” menu, select “Factory Settings”. Then select “Yes” and press
.
Your TV will go blank for a few seconds, then the “Initial Setup” menu will
appear. Your TV will be set to factory settings, but certain problems may be
solved.
Snowy picture,
noisy sound
Distorted picture,
noisy sound
Good picture,
noisy sound
No picture,
no sound
No sound or
inappropriate
sound
Good picture,
no sound
Dotted lines or
stripes
Double images or
“ghosts”
No color
Symptom Solutions
• Check the antenna cable and connection on the TV, VCR and at the wall
(see page 23).
• Check the antenna setup. Contact a Sony dealer for advice.
• Display the “Channel Setup” menu and select “Manual Program” to preset
the channel again (see page 21).
• Display the “Channel Setup” menu and set the “Signal Booster” to “Auto”
from “Manual Program” (see page 21).
• Try using an external booster.
• Turn off or disconnect the external booster if it is in use.
• Display the “Channel Setup” menu and set the “Signal Booster” to “Off”
from “Manual Program”(see page 21).
• Display the “Channel Setup” menu and select the appropriate
“TV System” from “Manual Program” (see page 21).
• Check the power cord, antenna and VCR connections (see page 23).
• Press ?/1 (power) to turn on the TV (see page 9).
• Press ! (main power) on the TV to turn off the TV for about five seconds,
then turn it on again (see page 8).
• Display the WEGA GATE menu and set the “Audio Input Fix” to “Off”
from “Party Mode Setup” (see page 12).
• Press 2 + to increase the volume level (see page 9).
• Press to cancel the muting (see page 9).
• Do not use a hair dryer or other equipment near the TV.
• Check the antenna setup. Contact a Sony dealer for advice.
• Use a highly directional antenna.
• Use the fine tuning (“Fine”) function (see page 21).
• Check the antenna setup. Contact a Sony dealer for advice.
• Turn off or disconnect the external booster if it is in use.
Display the “Picture” menu and select “Custom” from “Picture Mode”, then
adjust the “Color” level from “Picture Adjustment” (see page 18).
• Display the “Setup” menu and check the “Color System” setting
(usually set this to “Auto”) (see page 22).
• Check the antenna setup. Contact a Sony dealer for advice.
continue
01GB08ADV-SOEMRu.p65 9/5/05, 3:06 PM25
Black

Содержание

Скачать
Случайные обсуждения

Ответы 0

Микросхема УНЧ на мат.плате
3 года назад

Ответы 0

SONY SW292M91 Изночальная неисправность-заливает красным и обратный ход,пробитая оказалась TDA6108AJF,пробиты выводы питание 200v на IK и на и на выход красного катода,а также на вывод земля-оборван резистор 1 Ом по питанию TDA6108AJF,после замены микросхемы и резистора,темный экран,графики нет,с пульта управляется, громкость регулируется,слышны шумы,в режим AV переходит,слышно по исчезновению шумов,каналы переключяются,при добавлении ускоряющего появляется обратный ход с красной заливкой но не ярко,как обычно при добавлении ускорялки обратный ход и ярко белый фон.Откинул от IK стабилитрон тоже самое,на IK 2.6v. на входах видеоусилителя 2.6v, на выходе видеоусилителя 190v.Микросхема видеоусилителя заперта,не греется.При отключении катодов от платы кинескопа и замыкании их по очереди на бандаж кинескопа,по красному катоду сильно ярко заливает и срабатывает защита,на катоде красного отдельно от ПК измерял напряжение цифровым прибором показывает 90v.Подозрение на кинескоп,снял пк,все выводы на горловине соединеил с корпусом кроме двух фокусов,поочереди соединял выводы фокусов на присоску кинескопа,были ошеломляющие молнии в горловине кинескопа,после нескольких включений пропали и прошивало только на выводах горловины кинескопа,также подключял катод красного на присоску.После всех манипуляций одел плату кинескопа,запаял выводы на ПК,включил все без изменений.Подозрение на катод красного,проц не выдает RGB из за завышеного тока по катоду красного.Накал отдельно делал от сердечника ТДКСа. Кто знает подскажите как катод красного съэмулировать что бы не срабатывала защита по току,может между выводом катода и выходом видеоусилетеля поставить сопротивление.Телевизор у бабушки и ей очень нужно его сделать.Может я ошибаюсь по поводу кинескопа.Господа инженеры подскажите как решить этот трудный для меня вопрос
8 лет назад

Ответы 1

как добавить синего цвета
8 лет назад