Home
Главная
Oleo-Mac
Бензиновый Триммер
BC 24 T
Инструкция по эксплуатации Страница: 35

Oleo-Mac BC 24 T Инструкция по эксплуатации онлайн [35/246] 91721

makes it easier to collect, e.g. by raking.

• Try to work rhythmically. Stand firmly with

your feet apart. Move forward after the return

stroke and stand firmly again.

• Let the support cup rest lightly against the

ground. It is used to protect the blade from

hitting the ground.

• Reduce the risk of material wrapping around

the blade by following these instructions:

1. Always work at full throttle.

2. Avoid the previously cut material during the

return stroke.

• Stop the engine, unclip the harness and place

the machine on the ground before you start to

collect the cut material.

Grass trimming with a trimmer head

CAUTION: Do not work with mowing

line longer than the intended diameter. With

a properly mounted guard, the built-in cutter

will automatically adjust the line to its proper

length. Overly long lines can overload the

engine, resulting in damage to the clutch

mechanism and nearby parts.

Trimming

• Hold the trimmer head just above the ground

at an angle. It is the end of the cord that does

the work. Let the cord work at its own pace.

Never press the cord into the area to be cut.

• The cord can easily remove grass and weeds

up against walls, fences, trees and borders,

however it can also damage sensitive bark on

trees and bushes, and damage fence posts.

• Reduce the risk of damaging plants by

shortening the cord to 10-12 cm and reducing

the engine speed.

Clearing

• The clearing technique removes all unwanted

vegetation. Keep the trimmer head just above

the ground and tilt it. Let the end of the cord

strike the ground around trees, posts, statues

and the like (Fig.14).

CAUTION: This technique increases the

wear on the cord.

force. The tightening torque of the locking nut

should be 25 Nm.

• Check that the blade guard is not damaged or

cracked. Replace the blade guard if it is

cracked.

WARNING: Never use the machine

without a guard or with a defective guard.

Never use the machine without the

transmission shaft.

Forestry clearing

• Before you start clearing, check the clearing

area, the type of terrain, the slope of the

ground, whether there are stones, hollows etc.

• Start at whichever end of the area is easiest,

and clear an open space from which to work.

• Work systematically to and fro across the area,

clearing a width of around 4-5 m on each pass.

This exploits the full reach of the machine in

both directions and gives the operator a

convenient and varied working area to work

in.

• Clear a strip around 75 m long. Move your fuel

can as work progresses.

• On sloping ground you should work along the

slope. It is much easier to work along a slope

than it is to work up and down it.

• You should plan the strip so that you avoid

going over ditches or other obstacles on the

ground. You should also orient the strip to

take advantage of wind conditions, so that

cleared stems fall in the cleared area of the

stand.

Grass clearing using a grass blade

• Grass blades and grass cutters must not be

used on woody stems.

• A grass blade is used for all types of tall or

coarse grass.

• The grass is cut down with a sideways,

swinging movement, where the movement

from right-to-left is the clearing stroke and the

movement from left-to-right is the return

stroke. Let the left-hand side of the blade

(between 8 and 12 o’clock) do the cutting.

• If the blade is angled to the left when clearing

grass, the grass will collect in a line, which

Oleo-Mac BC 24 T Инструкция по эксплуатации онлайн [35/246] 91721

Содержание

Похожие устройства