Home
Главная
Skil
Шлифовальная Машина
9455 NA
Инструкция по эксплуатации Страница: 8

Skil 9455 NA Инструкция по эксплуатации онлайн [8/176] 92777

• Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) Maintainafirmgriponthepowertoolandposition

yourbodyandarmtoallowyoutoresistkickback

forces.Alwaysuseauxiliaryhandle,ifprovided,for

maximumcontroloverkickbackortorquereaction

duringstart-up.The operator can control torque reactions

or kickback forces, if proper precautions are taken.

b) Neverplaceyourhandneartherotatingaccessory.

The accessory may kickback over your hand.

c) Donotpositionyourbodyintheareawherepower

toolwillmoveifkickbackoccurs.Kickback will propel

the tool in the direction opposite to the wheel’s movement

at the point of snagging.

d) Usespecialcarewhenworkingcorners,sharp

edgesetc.Avoidbouncingandsnaggingthe

accessory.Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Donotattachasawchainwoodcarvingbladeor

toothedsawblade.Such blades create frequent

kickback and loss of control.

3)SAFETYWARNINGSSPECIFICFORGRINDINGAND

ABRASIVECUTTING-OFFOPERATIONS

a) Useonlywheeltypesthatarerecommendedfor

yourpowertoolandthespecificguarddesignedfor

theselectedwheel.Wheels for which the power tool

was not designed cannot be adequately guarded and are

unsafe.

b) Thegrindingsurfaceofthecentredepressed

wheelsmustbemountedbelowtheplaneofthe

guardlip. An improperly mounted wheel that projects

through the plane of the guard lip cannot be adequately

protected.

c) Theguardmustbesecurelyattachedtothepower

toolandpositionedformaximumsafety,sotheleast

amountofwheelisexposedtowardstheoperator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

d) Wheelsmustbeusedonlyforrecommended

applications.For example: Do not grind with the side of

a cut-o wheel. Abrasive cut-o wheels are intended for

peripheral grinding; side forces applied to these wheels

may cause them to shatter.

e) Alwaysuseundamagedwheelflangesthatareof

correctsizeandshapeforyourselectedwheel.

Proper wheel anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-o

wheels may be dierent from grinding wheel anges.

f) Donotuseworndownwheelsfromlargerpower

tools.A wheel intended for a larger power tool is not

suitable for the higher speed of a smaller tool and may

burst.

4)ADDITIONALSAFETYWARNINGSSPECIFICFOR

CUttING OFF OPERAtIONS

a) Donot“jam”thecut-offwheelorapplyexcessive

pressure.Donotattempttomakeanexcessivedepth

ofcut.Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

b) Donotpositionyourbodyinlinewithandbehind

therotatingwheel.When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

c) Whenthewheelisbindingorwheninterruptinga

cutforanyreason,switchoffthepowertooland

holdthepowertoolmotionlessuntilthewheel

comestoacompletestop.Neverattempttoremove

thecut-offwheelfromthecutwhilethewheelisin

motion,otherwisekickbackmayoccur.Investigate

and take corrective action to eliminate the cause of wheel

binding.

d) Donotrestartthecuttingoperationinthe

workpiece.Letthewheelreachfullspeedand

carefullyre-enterthecut.The wheel may bind, walk up

or kickback if the power tool is restarted in the workpiece.

e) Supportpanelsoranyoversizedworkpieceto

minimizetheriskofwheelpinchingandkickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Useextracautionwhenmakinga“pocketcut”into

existingwallsorotherblindareas.The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

5)SAFETYWARNINGSSPECIFICFORSANDING

OPERAtIONS

a) Whensanding,donotuseexcessivelyoversized

sandingdiscpaper.Followthemanufacturers’

recommendationswhenselectingsandingpaper.

Larger sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snagging,

tearing of the disc, or kickback.

6)SAFETYWARNINGSSPECIFICFORWIRE

BRUSHING OPERAtIONS

a) Beawarethatwirebristlesarethrownbythebrush

evenduringordinaryoperation.Donotoverstress

thewiresbyapplyingexcessiveloadtothebrush.

The wire bristles can easily penetrate light clothing and/

or skin.

b) Iftheuseofaguardisrecommendedforwire

brushing,donotallowanyinterferenceofthewire

wheelorbrushwiththeguard.Wire wheel or brush

may expand in diameter due to work load and centrifugal

forces.

GENERAl

• This tool is not suitable for wet grinding/cutting

• Only use the anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

• Alwaysdisconnectplugfrompowersourcebefore

makinganyadjustmentorchanginganyaccessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• Useonlygrinding/cuttingdiscswithamaximum

thicknessof8mmandaspindleholediameterof22

Skil 9455 NA Инструкция по эксплуатации онлайн [8/176] 92777

Содержание

Похожие устройства