Skil 3855 NA [16/204] Tool elements 5

Skil 3855 NA [16/204] Tool elements 5
16

Sliding mitre saw 3855
INTRODUCTION
This tool is intended as a stationary machine for
lengthways and crossways cutting of wood with straight
cuts as well as angle cuts (horizontal mitre angles of -47°
to +47° as well as vertical bevel angles of 0° to 45° are
possible)
The light of this power tool is intended to illuminate the
power tool΄s direct area of working operation and is not
suitable for household room illumination
Read and save this instruction manual 2
The sequence of the numbers appearing in the separate
assembly instruction sheet corresponds with the
sequence of the steps to be followed for assembling the
tool
Only use the tool when correctly and completely
assembled (be aware that Skil cannot be hold
responsible for tool damage and/or personal injuries
resulting from the incorrect assembly of the tool)
Before using the tool for the rst time, paste the supplied
sticker in your national language over the English text of
warning label A 5
TECHNICAL DATA 1
TOOL ELEMENTS 5
A Warning label
B Switch handle
C Locking pin for transport
D Safety lever
E Transport handle
F Mounting holes
G Support foot
H Dust bag
J Extension bars
J1 Knobs for locking extension bars
K Clamp for mounting workpiece
K1 Support hole (vertical clamping)
K2 Knob for fastening clamp
K3 Knob for adjusting clamp
K4 Clamping knob
K5 Knob for disassembling clamp
K6 Support hole (horizontal clamping)
L Fence
L1 Hex screws for adjusting fence (4x)
M Locking handle (mitre angles)
M1 Mitre angle indicator
N Locking knob (bevel angles)
N1 Bevel angle indicator
N2 Screw for adjusting bevel angle (right)
N3 Screw for adjusting bevel angle (left)
P Laser light
P1 On/o switch laser
Q Spot light
Q1 Switch for spot light
R Locking knob for slide device
S On/o switch
T1 Cutting depth limiter
T2 Depth stop
T3 Depth stop nut
V Length stop
V1 Locking knob for length stop
W Hex key
W1 Storage for hex key
W2 Spindle-lock button
W3 Blade bolt
W4 Lower guard
W5 Flange
W6 Upper guard
X Table insert
Y Cable storage hook
SAFETY
GENERAL SAFETY INSTRUCTIONS
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury. Save
all warnings and instructions for future reference. The
term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is
unavoidable, use an earth leakage circuit breaker.
Use of an earth leakage circuit breaker reduces the risk
of electric shock.

Содержание