Maxwell MW-1058 ST [8/24] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Maxwell MW-1058 ST [8/24] English

Maxwell MW-1058 ST [8/24] English
8
ENGLISH
• Do not leave children unattended not to let
them use the unit as a toy.
• For children safety reasons do not leave poly-
ethylene bags, used as a packaging, unat-
tended.
• Attention! Do not allow children to play
with polyethylene bags or packaging film.
Danger of suffocation!
• Never use the unit if the power cord or the
power plug is damaged, if the unit works
improperly or after it was dropped.
• Do not disassemble the unit by yourself, if
any malfunction is detected or after it was
dropped, apply to the nearest authorized
service center.
• Transport the unit in the original package
only.
• Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature, it is necessary to keep it for at
least two hours at room temperature.
– Unpack the kettle; remove any stickers that
can prevent unit operation.
– Check the unit for damages; do not use it in
case of damages.
– Make sure that the operating voltage of the
unit corresponds to the voltage of your mains.
– Insert the power plug into the mains socket,
you will hear a sound signal, the button (10)
illumination will flash 3 times.
– Take the kettle off the base (7) and open the
lid (4) by pressing the button (5).
– Fill the kettle with water till the «MAX» maxi-
mal water level mark, close the lid (4) tightly,
place the kettle on the base (7).
– Switch the kettle on by touching the button
(10), the flask (1) and the button (10) illumi-
nation will light up, and the symbol «100°» will
be flashing.
– Once water starts boiling, the kettle will be
switched off: there will be 3 sound signals,
the flask (1) and the button (10) illumination
will go out and the symbol «100°» will light
constantly.
– Pour out water, wait for 15-20 seconds and fill
the kettle with water again.
– Repeat the boiling procedure 2-3 times.
Note: Before removing the kettle from the base,
make sure that the boiling is over (the flask and
the button (10) illumination is off).
You will hear a sound signal when setting the
kettle on or removing it from the base.
USAGE
– Insert the power plug into the mains socket.
– Take the kettle off the base (7) and open the
lid (4) by pressing the button (5). Fill the ket-
tle with water making sure that the water level
is not below the minimal mark «MIN» and not
exceeding the maximal mark «MAX».
– Close the lid (4), place the kettle on the base
(7).
– Follow the recommendations in the corre-
sponding chapter (see below).
Water boiling
– Touch the button (10), the flask (1) and the
button (10) illumination will light up, and the
symbol «100°» will be flashing.
– Once water starts boiling, the kettle will be
switched off: there will be 3 sound signals,
the flask (1) and the button (10) illumination
will go out and the symbol «100°» will light
constantly.
– The temperature symbol illumination will go
out in 1 minute.
Maintaining temperature at 70°, 80°, 85°
or 90°с
– Touch the button (10).
– Select water temperature by touching the
buttons (9) ◄/►, the selected temperature
symbol will be flashing.
Note: If water temperature exceeds the
selected level, the unit will be switched to
the standby mode (the selected temperature
indicator will light constantly).
The keep warm function is not available for
100°С.
– Several seconds after setting the tempera-
ture the unit will start heating.
– Once the water reaches the set temperature,
you will hear 1 sound signal and the kettle will
be switched to the keep warm mode: once
the water temperature decreases, the heat-
ing is switched on automatically, when the
set temperature is reached, the unit will be
switched to the standby mode.
– The unit operates in the keep warm mode for
3 hours.
MW-1058.indd 8 21.01.2014 14:42:50

Содержание

Похожие устройства

Скачать