RCF NX L-23A Руководство по эксплуатации онлайн
Содержание
- Active 1
- English 2
- Important notes 2
- Safety precautions 2
- English 3
- Nx l23 a active line array module 3
- Nx series 3
- Operating precautions 3
- Touring audio solutions 3
- English 4
- Rear panel features and controls 4
- At this point you can connect the power supply cable and the signal cable but before turning on the speaker make sure that the volume control is at the minimum level even on the mixer output it is important that the mixer is already on before turning on the speaker this will avoid damage to the speakers and noisy bumps due to turning on parts on the audio chain it is a good practice to always turn on speakers at last and turn them off immediately after the show now you can turn on the speaker and adjust the volume control to a proper level 5
- Before turning on the speaker 5
- Connections 5
- English 5
- Pin 1 ground shield pin 2 hot pin 3 cold 5
- Reserved to the rcf service centre 5
- The xlr connectors use the following aes standard 5
- Volt 50 hz setup fuse value t5 al 250v 5
- Volt 60 hz setup fuse value t10 al 250v 5
- Voltage setup 5
- Warning always make sure that the maximum current requirement does not exceed the maximum admitted powercon current in case of doubt call the closest rcf service centre 5
- English 6
- Pole and tripod safety warnings 6
- Single nx l23 a 6
- Double nx l23 a on a stand 7
- English 7
- English 8
- General rigging warnings and safety precautions 8
- Nx l23 a suspended 8
- Rcf shape designer software and safety factor 8
- Connect the fly bar f to the chain hoist h o motors using a certified shackle secure the shackle to prevent un screwing following the shackle supplier instructions and warnings 10
- English 10
- Rigging procedure 10
- Rigging the system follow the procedure 10
- The nx l23 a fly bar 10
- The nx l23 a fly bar features 10
- English 11
- Array systems design 12
- Computer requirements 12
- English 12
- Installing rcf shape designer 12
- Rcf shape designer software 12
- English 13
- Introduction 13
- Using rcf shape designer software 13
- English 14
- Array installation 15
- Coverage 15
- English 15
- Number of cabinets and subwoofers 15
- Suspended mode 15
- Array page 16
- English 16
- Rcf shape designer results 16
- English 17
- Mechanics page 17
- Processor page 17
- English 18
- Manual mode 18
- Spl report page 18
- English 19
- High frequency equalization strategies 19
- Optimizing the array 19
- English 20
- Low frequency coupling effects 20
- Low frequency strategies 20
- English 21
- Nx l23 a ground stacked 21
- English 22
- Technical specifications 23
Похожие устройства
- RCF S5012 Руководство по эксплуатации
- RCF M602 Руководство по эксплуатации
- RCF M502 Руководство по эксплуатации
- RCF HS 2200 Руководство по эксплуатации
- RCF M1001 Руководство по эксплуатации
- RCF HL 2290 Руководство по эксплуатации
- RCF M1201 Руководство по эксплуатации
- RCF HDL 30-A (13000511) 72033594 Руководство по эксплуатации
- RCF HDL 18-AS Руководство по эксплуатации
- RCF HD 12-A MK4 Руководство по эксплуатации
- RCF HDL 28-A (13000579) 72036679 Руководство по эксплуатации
- RCF EVOX JMIX8 13000556 Руководство по эксплуатации
- RCF COMPACT M 08 Руководство по эксплуатации
- RCF COMPACT M 05 Руководство по эксплуатации
- RCF C 5215-99 Руководство по эксплуатации
- RCF EVOX 8 Руководство по эксплуатации
- RCF C 5215-66 Руководство по эксплуатации
- RCF C 5212-96 Руководство по эксплуатации
- RCF ART 735-A MK4 Руководство по эксплуатации
- RCF ART 725 Руководство по эксплуатации