![ALLEN & HEATH WZ4 14 [9/28] Connecting power](/img/pdf.png)
ALLEN & HEATH WZ4 14 [9/28] Connecting power
![ALLEN & HEATH WZ4 14 [9/28] Connecting power](/views2/1989975/page9/bg9.png)
Allen & Heath 9 WZ
4
14:4:2 User Guide
Connecting Power
Read and understand the Important Safety Instructions printed at the
start of this guide, and the warnings printed on the rear of the console. Check
that your local mains supply is within the 100-240V operating voltage range
allowed. Check that the correct mains lead with moulded plug has been sup-
plied with your console. Make sure that the IEC mains plug is pressed fully
into the panel socket before switching on.
Grounding
The connection to ground in an audio system is important for two reasons:
1. SAFETY - To protect the operator from high voltage electric shock, and
2. AUDIO PERFORMANCE - To minimise the effect of ground (earth) loops which result in
audible hum and buzz, and to shield the audio signals from interference.
3. For safety it is important that all equipment grounds are connected to mains ground so that
exposed metal parts are prevented from carrying high voltage which can injure or even kill the
operator. Do not disconnect the ground connection in the mains lead. It is recommended that
the system engineer check the continuity of the safety ground from all points in the system
including microphone bodies, turntable chassis, equipment cases, rack metalwork and so on.
Switching the console on and off
It is good practice to turn power amplifiers off before switching the console and any other con-
nected equipment on or off. This prevents any unexpected clicks or thumps when the equip-
ment is powered up.
Turn amplifiers and powered speakers on last and off first.
To turn the console on, press the ON/OFF switch next to the IEC mains input socket. To turn
the console off, press this switch again.
WARNING: THIS APPARATUS MUST BE EARTHED
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
RISK OF ELECTRIC SHOCK
CAUTION
DO NOT OPEN
ATTENTION: REMPLACER PAR UN FUSIBLE STRICTEMENT IDENTIQUE EN VALEURS.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE WITH SAME TYPE AND RATING.
100 - 240V~ 47-63Hz 45W MAX
AC MAINS IN ~
FUSE
T630mA L 250V 20mm
ON
I0
OFF
Serial No.ENGINEERED IN ENGLAND BY ALLEN & HEATH LIMITED
(1) this device may not cause harmful interference, and
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(2) this device must accept any interference received, including interference that may cause undesired operation.
MADE IN CHINA
CONFORMS TO ANSI/UL STD. 60065-2003
CERTIFICATED TO CAN/CSA STD.60065-03
Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan
Apparatet må tilkoples jordet stikkontakt
Apparaten skall anslutas till jordat uttag
CET APPAREIL DOIT ETRE MIS A LA TERRE
Содержание
- Mixwizard w 1
- Publication ap8666 1
- User guide 1
- Http www allen heath com 2
- Limited one year warranty 2
- Caution 3
- Safety instructions 3
- Warning this equipment must be earthed 3
- General precautions 4
- Important mains plug wiring instructions 4
- Safety instructions 4
- Contents 5
- Introduction 5
- 4 2 user guide 6
- Allen heath 6 w 6
- 2 3 4 5 6 7 8 7
- 2 and w 7
- 2 consoles are de scribed in separate publications for further information on the mixwizard series please refer to the allen heath web site 7
- 4 2 4 group model the 2 bus w 7
- 4 2 has 10 mono mic line inputs 2 fully featured dual input stereo channels and a 2 track replay input a total of 20 inputs to the mix of special note is the addition of a 2 x 6 way matrix providing a useful multi purpose output for those special demands such as recording and broadcast feeds delay fills zone feeds and so on a host of top end features are provided including oscillator and pink noise generator individual talkback to all outputs comprehensive engineer s metering and monitoring and a lamp socket 7
- 4 2 is equally at home mixing live shows recordings and corporate events tamperproof recessed switches configure the console for optimum foh or stage monitor operation this dual function ality pioneered by allen heath gives the con sole its unique ability to properly function as front of house or stage monitor or handle both at the same time ideal as a hard working work horse for hire stock touring and installed sound 7
- 4 2 user guide 7
- Ac mains in 7
- Allen heath 7
- Allen heath 7 w 7
- An allen heath ledlamp gooseneck lamp with built in dimmer can also be added for lighting the console in low light conditions 7
- Aux 5 aux 4 aux 3 aux 2 aux 1 7
- Caution 7
- Direct 7
- Direct out 7
- Insert 7
- Introducing the mixwizard w 7
- Line in 7
- Matrix out 7
- Mixwizard w 7
- Monitor out 7
- Multichannel audio usb 2 7
- Out direct 7
- Return 7
- The allen heath mixwizard series of consoles includes several models this user guide de scribes the w 7
- The aux and matrix outputs are impedance bal anced but may be electronically balanced if re quired by fitting an optional part a kit is also available to fit an optional usb2 output card which allows the console to be linked to a com puter for multitrack recording 7
- The base of the console can be removed to ac cess internal user selectable options these con figure user preference for the aux sends direct outputs and talkback mic phantom power 7
- The console can be operated free standing or in a 19 rack or flightcase it is supplied with pro tective side trims fitted these can be removed for rack mounting the rear connector pod can be easily rotated for rear facing or underside connectors when rack mounted 7
- The mixwizard is a compact console designed for professional sound mixing it is built to the same high standards as our top of the range con soles with individual circuit cards potentiome ters nutted to the panel for absolute strength steel chassis and no compromise circuit design ensuring the finest sonic performance 7
- Warning this apparatus must be earthed 7
- With its 4 band semi parametric eq 4 groups 6 auxes and stereo main output the w 7
- 4 2 user guide 8
- Allen heath 8 w 8
- Free standing 8
- Installing the console 8
- Rack mount 8
- Connecting power 9
- Grounding 9
- Read and understand the important safety instructions printed at the start of this guide and the warnings printed on the rear of the console check that your local mains supply is within the 100 240v operating voltage range allowed check that the correct mains lead with moulded plug has been sup plied with your console make sure that the iec mains plug is pressed fully into the panel socket before switching on 9
- Switching the console on and off 9
- 4 2 user guide 10
- Allen heath 10 w 10
- Headphones 10
- Input output 10
- Insert 10
- Pin 2 hot 10
- To from input output 10
- Y adapter 10
- 4 2 user guide 11
- A note about balanced connections 11
- Allen heath 11 w 11
- Audio connections 11
- Dealing with ground loops buzz and interference 11
- 4 2 user guide 12
- Allen heath 12
- Allen heath 12 w 12
- Mixwizard w 12
- 4 2 user guide 13
- Allen heath 13 w 13
- Direct outpu 13
- Insert 13
- Line tip tip in ring ring in 13
- Mic line i 13
- Return 13
- Stereo line i 13
- The console connectors 13
- Warning 13
- Aux out 1 14
- Group aux l r m ou 14
- Matrix out a 14
- Monitor ou 14
- Track in and ou 14
- Usb ii optio 14
- Pad line 15
- The mono input channel 15
- Aux send 16
- Routin 16
- Aux send 17
- Dual stereo input 17
- Routin 17
- Routing mode switc 17
- St1 st 17
- St2 st 17
- The stereo input channel 17
- Aux af 18
- Aux master 18
- Group af 18
- Group fade 18
- The group aux masters 18
- 4 2 can be configured as a compact yet fully featured monitor console 19
- 4 2 user guide 19
- A rotary control adjusts the level of the signal to the m output xlr the source is selected using the mode switch above the control this is recessed to prevent accidental operation use a pen or pointed object to set the position in the up position flush with the panel the post fade l and r mix is summed to provide a mono source use this in foh mode to feed a mono pa fill delay or zone speakers or even a mono broadcast or recording send 19
- Allen heath 19 w 19
- Aux 5 and 6 master 19
- Comprehensive engineer s headphones and local monitoring is provided 19
- Console monito 19
- In monitor mode press the switch to create an engineer s monitor wedge feed from the afl pfl mix it is common to use a wedge speaker of the same type used on stage to listen to and check the various monitor mixes being sent to the performers together with the group aux rev function the w 19
- Lr master 19
- M maste 19
- Select either lr or 2 track return as the default source using the l r 2trk switch pressing pfl or afl elsewhere on the console automatically overrides the current monitor source with the signal from the channel or mix selection the red pfl afl active indicator illuminates and the console meters display the active signal 19
- Separate faders control the main mix l and r output levels they provide 10db maximum boost each master includes a 4 led bar me ter an afl switch and a mute switch so that l and r can be separately moni tored and muted this is most useful in monitor mode where these masters carry the aux5 and aux6 signals 19
- The console main meters provide 12 led indicators to accurately display the signal level of the selected monitor source reduce the signal level if the red 16 peak indicator lights for optimum performance the signals meter an average 0 with loudest peaks reaching around 6 19
- The master section 19
- These function in the same way as described for auxes 1 to 4 the rev switch reverses the aux5 mix with l and aux6 mix with r for operation in monitor mode when selected the aux signals are presented to the l and r xlr outputs complete with their inserts the lr mix swaps on to the aux trs jack outputs note that the lr mix always feeds the matrix regardless of mode selected 19
- Use the monitor level control to adjust the level in the headphones and local speaker monitor we recommend you use closed ear headphones in the range 30 to 600 ohms designed for live sound monitoring headphones around 100 ohms impedance are a popular choice 19
- Warning to avoid damage to your hearing do not operate any close to ear monitoring such as headphones for long periods at high volume continued exposure to high volume sound can cause frequency selective or wide range hearing loss 19
- Signal generator pink nois 20
- Talkbac 20
- Talkback signal generator and matrix 20
- Mechanical 21
- Performance 21
- Specifications 21
- Connections 22
- Mixwizard 4 series part numbers 22
- 4 2 user guide 23
- Allen heath 23 w 23
- Block diagram 23
- Dual stereo inputs 23
- Groups aux 1 4 23
- L r aux 5 6 23
- Matrix a b 23
- Mic line inputs 23
- Monitor 23
- Wz4 14 4 2 23
- 4 2 user guide 24
- Allen heath 24 w 24
- Configure the internal options 24
- Important 24
- Refit the bas 24
- Remove the bas 24
- User options 24
- 4 2 user guide 25
- Allen heath 25 w 25
- Aux pre post insert e 25
- Channel aux pre post setting 25
- Direct output sourc 25
- Factory default for the mono channel pre fade auxes is pre insert pre eq this is popular with many users mixing monitors from foh it pre vents the channel eq and inserted compressors affecting the monitor mix move the jumper from a to b to change this to post insert post eq if preferred note that auxes are always post mute 25
- Factory default is aux 1 4 switched aux 5 6 switched you can change these settings for different combinations of pre post or switched auxes by cutting and re soldering the links refer to the system block diagram to explore the possibilities make sure you set all mono and stereo channels the same we rec ommend you only change these settings if absolutely necessary 25
- Factory default is pre fader this is common for live recording to multitrack the live mix fader movements do not affect the recording move the jump er from c to d to change to post fade post fade is appropri ate when using the output as a direct channel effects send 25
- L master talkback 48v 25
- Mono ch aux pre post eq 25
- Mono ch aux pre post fader 25
- Mono ch direct out 25
- Note that phantom power should not harm non powered dy namic microphones as long as balanced connections are used 25
- Solder options 25
- Stereo ch aux pre post fader 25
- Stereo ch mono stereo auxes 25
- Stereo channel aux pre post setting 25
- Stereo mono aux sourc 25
- Talkback mic 48 25
- The factory default is 48v phan tom power turned on for the front panel talkback mic xlr input the option jumper is behind the tb mic xlr on the l master board if you prefer phantom power can be disabled by repositioning the jumper to the gnd position 25
- The stereo channels can feed the auxes with a mono sum of l r or be configured so that l feeds the odd numbered auxes and r the even this is preferred when using odd even auxes as stereo pairs factory default is the mono setting 25
- Warning do not connect unbalanced sources or cables to inputs with phantom power select ed to avoid loud clicks do not press the talk switch when plugging or unplugging the talkback microphone 25
- 4 2 user guide 26
- Allen heath 26 w 26
- Aux 1 4 balance 26
- Aux5 balance 26
- Aux6 balance 26
- Group master r 26
- Master l 26
- Matrix ab balance 26
- Multichannel audio usb 2 26
- Output balance option 26
- Usb option 26
- 4 2 user guide 27
- Allen heath 27
- Allen heath 27 w 27
- Copy and use this page to record your console settings 27
- Cue sheet w 27
- Mixwizard w 27
Похожие устройства
- ALLEN & HEATH PL-7 Руководство по эксплуатации
- ALLEN & HEATH PL-5 Руководство по эксплуатации
- ALLEN & HEATH PL-12 Руководство по эксплуатации
- ALLEN & HEATH GL2400-24 Руководство по эксплуатации
- ALLEN & HEATH GL2400-16 Руководство по эксплуатации
- ALLEN & HEATH SQ-5 Руководство по эксплуатации
- ALLEN & HEATH Avantis Руководство по эксплуатации
- AKG WMS470 D5 SET BD8 (500-531) Руководство по эксплуатации
- AKG Perception Wireless 45 Vocal Set BD-U2 (614-634) Руководство по эксплуатации
- AKG WMS470 PRES SET BD7 (500-531) Руководство по эксплуатации
- AKG Perception Wireless 45 Vocal Set BD-A (530-560) Руководство по эксплуатации
- AKG Perception Wireless 45 Pres Set BD-U2 (614-634) Руководство по эксплуатации
- AKG Perception Wireless 45 Pres Set BD-A (530-560) Руководство по эксплуатации
- AKG Perception 420 Руководство по эксплуатации
- AKG Perception 170 Руководство по эксплуатации
- AKG D7 Руководство по эксплуатации
- Sennheiser RS120-8 II Руководство по эксплуатации
- AKG Perception Wireless 45 Sports Set BD-A (530-560) Руководство по эксплуатации
- APart AUDIOSYSTEM8.8 Руководство по эксплуатации
- Sennheiser G4ME Zero Руководство по эксплуатации