Home
Главная
BLACK & DECKER
Цепная пила
CS1835
Руководство по эксплуатации Страница: 10

BLACK & DECKER CS1835 [10/16] Checking and adjusting the chain tension fig i

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Checking and adjusting the chain tension (g. I)

Before use and after every 10 minutes of use, you must check

the chain tension.

u Disconnect the tool from the mains supply

u Lightly pull on the chain (5) as shown (inset g. I). The ten-

sion is correct when the chain (5) snaps back after being

pulled 3 mm away from the guide bar (4). There should be

no "sag" between the guide bar (4) and the chain (5) on

the underside.

Note: Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the guide bar and

the chain.

Note: When the chain is new, check the tension frequently

(after disconnecting from the mains) during the rst 2 hours of

use because a new chain stretches slightly.

To increase the tension (g. H)

u Turn the chain adjust locking knob (7) counterclockwise.

u Tension the chain using the chain tension adjusting screw

(8), turn clockwise to tighten.

u Tighten the chain adjust locking knob (7).

Use

Warning! Let the tool work at its own pace. Do not overload.

Filling the oil reservoir (g. K)

u Remove the oil cap (12) and ll the reservoir with the

recommended chain oil. You can see the oil level in the oil

level indicator (13). Ret the oil cap (12).

u Periodically switch off and check the oil level indicator

(13); if it is less than a quarter full, disconnect your chain-

saw from the mains supply and rell with the correct oil.

This chainsaw is equipped with an automatic oiling system

that keeps the saw chain and guide bar constantly lubricated.

We recommend that you use only BLACK+DECKER oil during

the lifetime of your chainsaw because mixtures of different oils

could lead to the oil becoming degraded, which can drastically

shorten the lifetime of the saw chain and create additional

risks.

Never use waste oil, thick oil or very thin sewing machine

oil. These may damage your chainsaw .Only use the correct

grade of oil (cat. no. A6023-QZ).

u The chain saw will automatically feed oil to the chain dur-

ing use.

Switching on

Note: It will not be possible to switch the tool on if the front

guard/chain brake assembly is not in the "set" position.

u Grip your chainsaw rmly with both hands. Push the lock-

off button (2) and then push the on/off switch (1) to start.

u When the motor starts, remove your thumb from the lock

button (2) and grip the handle rmly.

Do not force the tool, allow the tool to do the work. It will do

a better and safer job at the speed for which it is designed.

Excessive force will stretch the saw chain (5).

How to set the chain brake (g. A)

u Make sure that the tool is disconnected from the mains

supply.

u Pull the front guard/chain brake assembly (3) back into the

"set" (g. A) position.

u The tool is now ready to use.

How the anti-kickback chain brake works

In the event of kickback, your left hand comes in contact with

the front guard, pushing it forwards, toward the workpiece,

and stops the tool within a few fractions of a second.

How to test the anti-kickback chain brake (fig. A)

u Always check that the kickback brake operates correctly

before use.

u Grip the tool firmly in both hands on a firm surface make

sure the saw chain (5) is clear of the ground and switch on

(see" How to switch the chainsaw on").

u Rotate your left hand forward around the front handle so

that the back of your hand comes in contact with the front

guard/chain brake assembly (3) and push it forwards,

toward the workpiece (fig. A). The saw chain (5) should

stop within a few fractions of a second.

To reset after the operation of the front guard/chain brake

assembly (3) follow the instructions for "How to set the chain

brake".

Note: Avoid re-starting the tool until you hear the motor come

to a complete rest.

Note: If chain brake in malfunctioning take the product to an

approved BLACK+DECKER service centre.

If the saw chain (5) or guide bar (4) becomes jammed

u Switch the tool off.

u Disconnect the tool from the mains supply.

u Open the cut with wedges to relieve the strain on the

guide bar (4). Do not try to wrench the chainsaw free.

u Start a fresh cut.

Felling (g. L - R)

Inexperienced users should not attempt to fell trees. The user

may suffer injury or cause damage to property as a result of

failure to control the direction of fall, the tree may splinter or

damaged/dead branches may fall during cutting.

The safe distance between a tree to be felled and bystanders,

buildings and other objects is at least 2 1/2 times the height of

the tree. Any bystander, building or object within this distance

is at risk from being struck by the tree when felled.

Before attempting to fell a tree:

u Make sure that there are no local by-laws or regulations

that would prohibit or control the felling of the tree.

u Consider all conditions that may affect the direction of fall,

including:

u The intended direction of fall.

u The natural lean of the tree.

u Any unusual heavy limb structure or decay.

u Surrounding trees and obstacles including overhead

lines and underground drains.

u The wind speed and direction.

Pre-plan a safe exit from falling trees or branches. Make sure

that the exit route is clear of obstacles that would prevent or

hinder movement. Remember that wet grass and freshly cut

bark is slippery.

BLACK & DECKER CS1835 [10/16] Checking and adjusting the chain tension fig i

Содержание

Похожие устройства