![Gigabyte B365 S1151 MATX B365M H [37/44] Chapter 3 appendix](/img/pdf.png)
Gigabyte B365 S1151 MATX B365M H [37/44] Chapter 3 appendix
![Gigabyte B365 S1151 MATX B365M H [37/44] Chapter 3 appendix](/views2/2002888/page37/bg25.png)
Chapter 3 Appendix
3-1 ConguringaRAIDSet
RAID Levels
Before you begin, please prepare the following items:
• AtleasttwoSATAharddrivesorSSDs.
(Note1)
(To ensure optimal performance, it is recommended that you
usetwoharddriveswithidenticalmodelandcapacity).
(Note2)
• Windows setup disk.
• Motherboard driver disk.
• A USB thumb drive.
ConguringtheOnboardSATAController
A. Installing SATA hard drive(s) in your computer
Installtheharddrives/SSDsintheIntel
®
Chipset controlled connectors on the motherboard. Then connect the
power connectors from your power supply to the hard drives.
B.ConguringSATAcontrollermodeinBIOSSetup
MakesuretoconguretheSATAcontrollermodecorrectlyinsystemBIOSSetup.
Steps:
1. Go to Peripherals\SATAAndRSTConguration, make sure SATA Controller(s) is enabled. To create
RAID,setSATA Mode Selection to Intel RST Premium With Intel Optane System Acceleration. Then
savethesettingsandrestartyourcomputer.Note:WhenusingaPCIeSSD,makesuretosettheUSE RST
Legacy OROM item under Peripherals\SATAAndRSTConguration to Disabled. Then depending the
M.2 connector you use, set the corresponding PCIe Storage Dev on Port XX item to RST Controlled.
2. TousetheEZRAIDfeature,followthestepsin"C-1."TocongureUEFIRAID,followthestepsin"C-2."To
enterthelegacyRAIDROM,referto"C-3"formoreinformation.Finally,savethesettingsandexitBIOSSetup.
C-1. Using EZ RAID
GIGABYTEmotherboardsprovideyouwith theEZRAIDfeature,allowing youtoquicklycongurea RAID
arraywithsimpliedsteps.
Steps:
1. After restarting the computer, enter the BIOS Setup and go to Peripherals.Press<Enter>ontheEZ RAID
item.SelectthetypeofharddrivesyouuseforRAIDintheTypetabandthenpress<Enter>.
2. Go to the ModetabtoselectaRAIDlevel.RAIDlevelssupportedincludeRAID0,RAID1,RAID10,andRAID5
(theselectionsavailabledependonthenumberoftheharddrivesbeinginstalled).Thenpress<Enter>to
move to the Create tab. Click Proceed to begin.
RAID 0 RAID 1 RAID 5 RAID 10
Minimum
Number of Hard
Drives
≥2 2 ≥3 4
Array Capacity Number of hard
drives*Sizeofthe
smallest drive
Sizeofthesmallest
drive
(Number of hard
drives-1)*Sizeof
the smallest drive
(Number of hard
drives/2)*Sizeofthe
smallest drive
Fault Tolerance No Yes Yes Yes
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
(Note1) AnM.2PCIeSSDcannotbeusedtosetupaRAIDsetwithaSATAharddrive.
(Note2) Referto"1-7InternalConnectors,"fortheinstallationnoticesfortheM.2andSATAconnectors.
- 37 -
Содержание
- B365m h 1
- Rev 1001 1
- User s manual 1
- Copyright 2
- Disclaimer 2
- Identifying your motherboard revision 2
- B365m h motherboard layout 3
- Chapter 1 hardware installation 3
- Chapter 2 bios setup 8 3
- Chapter 3 appendix 7 3
- Table of contents 3
- B365m h 4
- B365m h motherboard 5 two sata cables 4
- B365m h motherboard layout 4
- Box contents 4
- Motherboard driver disk 5 i o shield 4
- User s manual 4
- 1 installation precautions 5
- Chapter 1 hardware installation 5
- 2 productspecifications 6
- 3 installing the cpu 9
- 4 installing the memory 9
- Dualchannelmemoryconfiguration 9
- Installing the cpu 9
- 5 installing an expansion card 10
- 6 back panel connectors 10
- D sub port 10
- Hdmi port 10
- Ps 2 keyboard and ps 2 mouse port 10
- Usb 3 gen 1 port 10
- Audiojackconfigurations 11
- Device and then remove it from the motherboard 11
- Line in rear speaker out blue 11
- Line out front speaker out green 11
- Mic in center subwoofer speaker out pink 11
- Pleasevisitgigabyte swebsitefordetailsonconfiguringtheaudiosoftware 11
- Prevent an electrical short inside the cable connector 11
- Rj 45 lan port 11
- The gigabit ethernet lan port provides internet connection at up to 1 gbps data rate the following describesthestatesofthelanportleds 11
- The line in jack use this audio jack for line in devices such as an optical drive walkman etc 11
- The line out jack 11
- The mic in jack 11
- Theusbportsupportstheusb2 1 specification usethisportforusbdevices 11
- Toconfigure7 channelaudio youhavetouseanhdfrontpanelaudiomoduleandenablethe multi channel audio feature through the audio driver 11
- Usb 2 1 port 11
- Whenremovingthecable pullitstraightoutfromtheconnector donotrockitsidetosideto 11
- Whenremovingthecableconnectedtoabackpanelconnector firstremovethecablefromyour 11
- 7 internal connectors 12
- 2 atx_12v_2x4 atx 2x4 12v power connector and 2x12 main power connector 13
- 4 cpu_fan sys_fan fan headers 13
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 13
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from 13
- Overheating overheating may result in damage to the cpu or the system may hang 13
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 13
- Thesefanheadersarenotconfigurationjumperblocks donotplaceajumpercapontheheaders 13
- To meet expansion requirements it is recommended that a power supply that can withstand high powerconsumptionbeused 500worgreater ifapowersupplyisusedthatdoesnotprovidethe required power the result can lead to an unstable or unbootable system 13
- With the use of the power connector the power supply can supply enough stable power to all the components onthemotherboard beforeconnectingthepowerconnector firstmakesurethepowersupplyisturned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 13
- Chipsetsupportsraid0 raid1 raid5 andraid10 refertochapter3 configuringaraidset forinstructionsonconfiguring araidarray 14
- Followthestepsbelowtocorrectlyinstallanm ssdinthem connector step 1 locatethepropermountingholeforthem ssdtobeinstalledandtheninstallthemountingclipfirst step 2 slidethem ssdintotheconnectoratanangle step 3 pressthem ssddownandthensecureitbypressingtheclippinintothemountinghole 14
- M2m m socket 3 connector 14
- Pin no definition 14
- Sata3 2 3 4 5 sata 6gb s connectors 14
- Selecttheproperholeforthemountingclipaccordingtothelengthofthem ssdtobeinstalled 14
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the inte 14
- Them connectorsupportsm satassdsorm pciessdsandsupportraidconfiguration please notethatanm pciessdcannotbeusedtocreatearaidsetwithasataharddrive tocreatearaid arraywithanm pciessd youmustsetuptheconfigurationinuefibiosmode refertochapter3 configuringaraidset forinstructionsonconfiguringaraidarray 14
- Toenablehot pluggingforthesataports refertochapter2 biossetup peripherals sata andrstconfiguration formoreinformation 14
- Ci chassisintrusionheader connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed this function requires a chassis with a chassis intrusion switch sensor 15
- Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below note the positive and negative pins before connecting the cables 15
- Connects to the power status indicator onthechassisfrontpanel theledison whenthesystemisoperating theledis off when the system is in s3 s4 sleep state orpoweredoff s5 15
- F_audio front panel audio header 15
- F_panel front panel header 15
- Gnd 7 faudio_jd 15
- Hd harddriveactivityled connectstotheharddriveactivityledonthechassisfrontpanel theledisonwhentheharddrive is reading or writing data 15
- Line2_r 10 sense 15
- Mic2_l 6 sense 15
- Mic2_r 8 no pin 15
- Nc 9 line2_l 15
- Nc no connection 15
- Pin no definition pin no definition 15
- Pled pwr_led powerled 15
- Pw powerswitch connects to the power switch on the chassis front panel you may configurethewaytoturnoffyoursystemusingthepowerswitch refer tochapter2 biossetup power formoreinformation 15
- Res resetswitch connects to the reset switch on the chassis front panel press the reset switch to restart the computer ifthecomputerfreezesandfailstoperformanormalrestart 15
- S3 s4 s5 off 15
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 15
- Speak speaker connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup 15
- System status led 15
- The front panel design may differ by chassis a front panel module mainly consists of power switch resetswitch powerled harddriveactivityled speakerandetc whenconnectingyourchassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly 15
- Thefrontpanelaudioheadersupportshighdefinitionaudio hd youmayconnectyourchassisfront panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 15
- Donotplugtheieee1394bracket 2x5 pin cableintotheusb2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord 16
- F_usb1 f_usb2 usb 2 1 headers 16
- F_usb30 usb 3 gen 1 header 16
- From the power outlet to prevent damage to the usb bracket 16
- Theheaderconformstousb3 gen1andusb2 specificationandcanprovidetwousbports for purchasingtheoptional3 frontpanelthatprovidestwousb3 gen1ports pleasecontactthelocal dealer 16
- Theheadersconformtousb2 1 specification eachusbheadercanprovidetwousbportsviaan optional usb bracket for purchasing the optional usb bracket please contact the local dealer 16
- Tpm trusted platform module header 16
- Youmayconnectatpm trustedplatformmodule tothisheader 16
- Bat battery 17
- Clr_cmos clear cmos jumper 17
- Com serial port header 17
- 1 startup screen 18
- Chapter 2 bios setup 18
- 2 the main menu 19
- Classic setup function keys 19
- 3 m i t 20
- C10 state support 21
- C3 state support 21
- C6 c7 state support 21
- C8 state support 21
- Cpu enhanced halt c1e 21
- Cpu flex ratio override 21
- Cpu flex ratio settings 21
- Hyper threading technology 21
- Intel r speed shift technology inte 21
- Intel r turbo boost technology 21
- No of cpu cores enabled 21
- Speed shift technology 21
- Turbo rati 21
- Uncore frequency 21
- Adjacent cache line prefetch 22
- Cpu eist function 22
- Cpu thermal monitor 22
- Energyefficientturb 22
- Extremememoryprofile x m p 22
- Hardware prefetcher 22
- Memory frequency mhz 22
- Memory odd ratio 100 133 or 200 266 22
- Memory ref clock 22
- Package c state limit 22
- Race to halt rth 22
- Ring to core offset down bin 22
- System memory multiplier 22
- Voltage optimization 22
- Advanced memory settings 23
- Channel a b memory sub timings 23
- Channel interleaving 23
- Extremememoryprofile x m p 23
- Memory boot mode 23
- Memory enhancement settings 23
- Memory multiplier tweaker 23
- Memory odd ratio 100 133 or 200 266 memory frequency mhz 23
- Memory timing mode 23
- Profileddrvoltage 23
- Rank interleaving 23
- Realtime memory timing 23
- System memory multiplier memory ref clock 23
- 3dmark01 enhancement 24
- Advanced power settings 24
- Advanced voltage settings 24
- Case open 24
- Cpu core voltage control 24
- Cpu vcore cpu vccsa dram channel a b voltage 3 v 5v 12v cpu vaxg 24
- Cpu vcore loadline calibration 24
- Dram voltage control 24
- Fan speed control 24
- Internal vr control 24
- Max link speed 24
- Miscellaneous settings 24
- Monitor 24
- Pc health status 24
- Reset case open status 24
- Smart fan 5 settings 24
- Fan control mode 25
- Fan control use temperature input 25
- Fan fail warning 25
- Fan speed 25
- Fan stop 25
- Temperature 25
- Temperature interval 25
- Temperature warning control 25
- 4 system 26
- Access level 26
- System date 26
- System language 26
- System time 26
- 5 bios 27
- Boot option priorities 27
- Bootup numlock state 27
- Fast boot 27
- Full screen logo show 27
- Hard drive cd dvd rom drive floppy drive network device bbs priorities 27
- Security option 27
- Csm support 28
- Lan pxe boot option rom 28
- Mouse speed 28
- Network stack driver support 28
- Next boot after ac power loss 28
- Ps2 devices support 28
- Sata support 28
- Storage boot option control 28
- Usb support 28
- Vga support 28
- Administrator password 29
- Other pci devices 29
- Secure boot 29
- User password 29
- 6 peripherals 30
- Above 4g decoding 30
- Ez raid 30
- Initial display output 30
- Intel platform trust technology ptt 30
- Onboard lan controller 30
- Realtek pcie gbe family controller 30
- Rgb fusion onboard led 30
- Sw guard extensions sgx 30
- Aggressive lpm support 32
- Configuredasesata 32
- Hot plug 32
- Mechanical presence switch 32
- Nvmeconfiguration 32
- Port 0 2 3 4 5 32
- Sata controller s 32
- Sata mode selection 32
- Sataandrstconfiguration 32
- 7 chipset 33
- Audio controller 33
- Dvmt pre allocated 33
- Dvmt total gfx mem 33
- Internal graphics 33
- Ioapic 24 119 entries 33
- 8 power 34
- Ac back 34
- Dmi aspm 34
- Pch aspm 34
- Peg aspm 34
- Platform power management 34
- Power on by keyboard 34
- Power on password 34
- Cec 2019 ready 35
- Power loading 35
- Power on by mouse 35
- Rc6 render standby 35
- Resume by alarm 35
- Soft off by pwr bttn 35
- 9 save exit 36
- Boot override 36
- Exit without saving 36
- Load optimized defaults 36
- Loadprofiles 36
- Save exit setup 36
- Saveprofiles 36
- 1 configuringaraidset 37
- A installing sata hard drive s in your computer 37
- B configuringsatacontrollermodeinbiossetup 37
- Before you begin please prepare the following items 37
- C 1 using ez raid 37
- Chapter 3 appendix 37
- Configuringtheonboardsatacontroller 37
- Raid levels 37
- C 2 uefiraidconfiguration 38
- C 3 configuringlegacyraidrom 38
- 2 installing an inte 39
- Install the sata raid ahci driver and operating system 39
- Installation guidelines a 1 installation in ahci mode 39
- Installing the operating system 39
- Memory 39
- System requirements 39
- A 2 installation in intel rst premium with intel optane system acceleration mode 40
- 3 drivers installation 41
- Battery information 42
- Our commitment to preserving the environment 42
- Regulatory notices 42
- Regulatory statements 42
- Restriction of hazardous substances rohs directive statement 42
- Waste electrical electronic equipment weee directive statement 42
- Weee symbol statement 42
- Canada industry canada ic notices canada avis d industry canada ic 43
- Fcc notice u s a only 43
- Contact us 44
- Gigabyte esupport 44
- Tosubmitatechnicalornon technical sales marketing question pleaselinkto https esupport gigabyte com 44
Похожие устройства
- Corsair HS50 CA-9011170-EU Руководство по эксплуатации
- Corsair Gaming Void Pro Surround CA-9011157-EU Руководство по эксплуатации
- Corsair Gaming HS60 Surround Gaming Headset Руководство по эксплуатации
- Corsair Gaming K95 RGB Platinum MX Speed Руководство по эксплуатации
- Dell UltraSharp U3419W Руководство по эксплуатации
- ASRock AMD B350 SAM4 MATX AB350M-HDV R4.0 Руководство по эксплуатации
- ASRock AMD X570 SAM4 ATX X570 TAICHI Руководство по эксплуатации
- ASRock AMD A320 SAM4 MATX A320M-DVS R4.0 Руководство по эксплуатации
- Asus X512FA 90NB0KR6-M06440 Руководство по эксплуатации
- Asus X543UA-GQ1836T 90NB0HF7-M28560 Руководство по эксплуатации
- Asus X510QR (Pronet Q1-20) 90NB0ME2-M01200 Руководство по эксплуатации
- Asus X512FA 90NB0KR3-M06430 Руководство по эксплуатации
- Asus UX333FA-A3018T Руководство по эксплуатации
- Asus ROG Strix Impact II 90MP01E0-B0UA00 Руководство по эксплуатации
- ASRock AMD A320 SAM4 MATX A320M PRO4 R2.0 Руководство по эксплуатации
- Asus ROG Strix Impact 90MP00P0-B0UA00 Руководство по эксплуатации
- Asus ROG Sica Steel 90MP00B1-B0UA00 Руководство по эксплуатации
- Asus UX534FTC (Q1-20) 90NB0NK3-M03680 Руководство по эксплуатации
- Asus GTX1650 4GB PH-GTX1650-O4G Руководство по эксплуатации
- Asus GTX1050TI 4GB PH-GTX1050TI-4G Руководство по эксплуатации