Rovus GS-XH026 [7/100] Caution please make sure not to fill over max water lever marked on the tank be sure to disconnect the power plug when removing the water tank or cleaning

Rovus GS-XH026 [7/100] Caution please make sure not to fill over max water lever marked on the tank be sure to disconnect the power plug when removing the water tank or cleaning
7
shock or re.
27. Do not use near furnaces, replaces, stoves or other high temperature heat sources.
28. The appliance should not be forcefully turned or oscillated, under any circumstances.
This will cause damage to the oscillation mechanism.
29. This device is tted with automatic cut-o switches that operate if it tips over or
overheats. If the switches operate, check the device, position it back on hard and
level surface before reusing.
30. Although the device has been checked its usage and consequences are strictly user
responsibility.
PARTS (See Picture 1)
1. Middle cover
2. Main body
3. Power switch
4. Fan blades
5. Front mesh
6. Water inlet plugs
7. Water inlet
8. Mist nozzle
9. Water tank
10. Digital display
OPERATING PANEL (See Picture 2)
Normal air ow: at this mode, ow will change according to surrounding temperature.
Natural air ow: this mode imitates the natural light wind, which gives a unique nature experience indoor.
Sleep air ow: at this mode the ow will drop from intial setting, which was set by user. Then it will drop one step every 30 minutes until nally running at rst step.
OPERATING INSTRUCTIONS (See Picture 3)
How to ll water into water tank
1. Slide out the water tank from the main body. (Picture 3, Fig. A)
2. Lift the plug of the inlet, ll the clean water into the tank, and reposition the plug when lled with water. Slide the water tank back into the main body. (Picture 3, Fig. B)
CAUTION: Please make sure not to ll over max water lever marked on the tank. Be sure
to disconnect the power plug when removing the water tank or cleaning.
3. Plug into power supply and ensure the voltage is 230 V. After pressing the »I« on power switch, the device will bip and the digital display will show the temperature and humidity.
OPERATING PANEL SYMBOLS (See Picture 4)
ON/OFF (Picture 4, Fig. A)
Press this symbol to turn on or o the unit. When power on, the water container light turns blue and the unit starts to work at rst gear, without heating or humidication.
HEATING (Picture 4, Fig. B)
Press this symbol to turn on to heating mode - the light turns to red. Fan speed locks to speed 1, press again to switch back to the recirculating wind mode.
HUMIDIFYING (Picture 4, Fig. C)
Press this symbol to turn on humidication. Press again to turn o .
NOTE: Mist nozzle might get obstructed by water. Turn o the device and wipe it gently o with a soft cloth.
WIND TYPE (Picture 4, Fig. D)
Press this symbol to switch between dierent wind types from normal to natural to the recirculating wind function and set the type of wind. Each press will switch from normal wind to natural
wind to sleep wind circularly.
SIDE TO SIDE PIVOTING (Picture 4, Fig. E)
Press this symbol to adjust left and right. Press again to switch o.
UP AND DOWN PIVOTING (Picture 4, Fig. F)
Press this symbol to move fan up and down. Press again to switch o .
PLUS AND MINUS (Pcture 4, Fig. G and H)
1. Press to switch between 12 levels o fair ow speed.
2. In heating mode press to switch between 2 levels of heating.
11. Operating panel
12. Remote controller
13. Stand
14. Handle
15. Rear mesh
16. Motor
17. Electric heating wire
18. Aroma box
19. Power cord

Содержание

Похожие устройства

Скачать
Случайные обсуждения

Ответы 0

Можно схему
1 год назад

Ответы 0

Ремонт печатной платы
1 год назад

Ответы 0

Ремонт схема элктромотор
1 год назад