Rovus GS-XH026 [8/100] Warning please be sure to turn off the power and remove the mains plug from the wall socket before cleaning the motor may be hot after usage so let it cool down before cleaning

Rovus GS-XH026 [8/100] Warning please be sure to turn off the power and remove the mains plug from the wall socket before cleaning the motor may be hot after usage so let it cool down before cleaning
8
LIGHT (Picture 4, Fig. I)
Press this symbol to turn on or o the display.
TIMER SETTINGS (Picture 4, Fig. J)
Press this symbol to set the timer from 0,5 to 7,5 hours with each press. Keep pressing to switch o.
REMOTE CONTROL (See Picture 5)
1. Remove the battery protective lm before operating.
2. Operate the remote when pointing to the device.
3. Battery replacement: when the remote control decreases the operating range or the main body does not response, please replace the battery.
REMOTE CONTROL FUNCTIONS (See Picture 6)
1. ON/OFF
2. Plus and minus function
3. Side to side/ Up and down function
4. Timer
5. Heating
6. Light
7. Wind type
8. Humidifying
AROMA BOX (See Picture 7)
1. Remove the aroma box cover and take out the aroma tray. (Picture 7)
2. Pour 1-2drops of aromatic water into the box and insert back to reposition the cover. (Picture 7)
PRODUCT USAGE (See Pictures 8 and 9)
Please place product on even and non-obstructed surface.
1. Recirculating fan usages
a. Cold/ heating room air circulation (Picture 8, Fig. A)
b. Indoor and outdoor air exchange circulation (Picture 8, Fig. B)
c. Indoor air circulation (Picture 8, Fig. C)
d. Indoor clothes dryer (Picture 8, Fig. D)
2. Heating function (Picture 9, Fig. A)
3. Humidifying function (Picture 9, Fig. B)
MAINTENANCE AND STORAGE
Clean regularly to prevent potential breakdown due to potential accumulation of dust.
WARNING: Please be sure to turn o the power and remove the mains plug from the
wall socket before cleaning. The motor may be hot after usage so let it cool down before
cleaning.
HOW TO CLEAN MAIN BODY (See Picture 10)
Remove the mesh cover for cleaning
a. Locate the ap on mesh cover. First, nd the lock switch of the back cover.
b. Push on the ap clockwise to unlock and remove the mesh cover. (Picture 10)
c. Use a vacuum cleaner to clean up the dust in the mesh cover. (Picture 10)
d. Use a soft cloth to wipe the mesh cover. (Picture 10)
e. When nish cleaning, reposition the mesh cover and turn counter clockwise to lock the cover.
WATER TANK CLEANING
•
Be sure to disconnect the power plug when removing the water tank to feed water or before cleaning.
•
Remove the water tank from the main body, and then rinse inside of the water tank with tap water; use a damp cloth to clean the mist nozzle.
•
If you experience any diculties with limescale (due to local hard water) you can pour small amount of vinegar inside the tank and on the mist nozzle, wait for approximately 20 minutes
and then rinse well with tap water; use a damp cloth to clean the mist nozzle.
STORAGE
If unused for a long time, please clean as per above instruction and dry completely the water tank before storing.
TROUBLESHOOTING GUIDE
Please read the instructions carefully before sending to repair.
Problem Possible cause Solution
Product does not work. Power plug is not properly inserted into the socket. Reconnect the power cord and make sure it is
correctly inserted into the socket.
Product makes abnormal noise when operating. The main body is not in horizontal position. Place the appliance on an even surface.
Product does not produce wind. Dust buildup. Make sure product is cleaned and maintained
regularly.
Product can be heard while rotating. This is a motor running specic sound. /
Mist does not come out when in humidifying mode. 1. There is limescale on the mist nozzle.
2. Product hasn’t been used for a longer period of
time.
1. Clean the mist nozzle (see water tank cleaning).
2. Clean the water tank (see water tank cleaning).
If any type of other problem occurs, please contact your local supplier.

Содержание

Похожие устройства

Скачать
Случайные обсуждения

Ответы 0

Можно схему
1 год назад

Ответы 0

Ремонт печатной платы
1 год назад

Ответы 0

Ремонт схема элктромотор
1 год назад