Home
Главная
Bosch
Автомойки
AdvancedAquatak 150 2200Вт
Руководство по эксплуатации Страница: 17

Bosch AdvancedAquatak 150 2200Вт [17/298] Mounting and operation

English | 17

3 600 HA7 7.. 3 600 HA7 8..

Vibration total values a

(triax vector sum) and uncertainty K determined according to EN60335-2-79

– Vibration emission value a

m/s

3.2 2.9

– Uncertainty K m/s

1.0 1.0

Mounting and Operation

Action Figure Page

Delivery scope

A 281

Adjusting the Handle

B 282

Connecting high pressure wa-

ter supply hose/nozzle

C 282

Connecting to the water supply

D 283

Switching On and Off

E – F 283

Clean the water filter

G 284

Clean nozzle

H 284

Connecting high pressure gun

to lance

I 284

Tube Assembly

J 285

Connect detergent bottle

K 285

Variable Fan lance

Connecting high pressure gun

to lance

Adjust water jet

L 286

Roto lance

Connecting high pressure gun

to lance

Adjust water jet

M 287

Gun storage

N 288

Storage

O 288

Transport

P 289

Selecting Accessories

Q 290

Switching on

For Your Safety

Warning: Switch off, remove plug from

mains before adjusting, cleaning or if cable

is cut, damaged or entangled.

The operating voltage is 230VAC, 50Hz (for non-EU coun-

tries 220V, 240V as applicable). Contact your Bosch Ser-

vice Centre for details. If in doubt contact a qualified electri-

cian or the nearest Bosch Service Centre.

If you want to use an extension cable when operating your

high pressure washer, only the following cable dimensions

should be used:

– 2.5mm

– max length 25m

Note: If an extension cable is used it must be earthed and

connected through the plug to the earth cable of your supply

network in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest

Bosch Service Centre.

WARNING! Inadequate extension cables can

be dangerous. Extension cable, plug and

socket must be of watertight construction

and intended for outdoor use.

The connections (plugs and sockets) should be kept dry and

off the ground.

For increased electrical safety use a Residual Current Device

(RCD) with a tripping current of not more than 30mA. Al-

ways check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a

Bosch Service Centre.

For products not sold in GB:

Warning: For your safety, it is required that the plug at-

tached to the product is connected with the extension cord.

The coupling of the extension cord must be protected

against splash water, be made of rubber or coated with rub-

ber. The extension cord must be used with a cable strain re-

lief.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an au-

thorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

u Products that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Operation

u To prevent damage to the appliance, do not allow it to

operate dry.

Starting

Attach water supply hose (not supplied) to the mains water

supply and machine.

Connect the product to the mains supply ensuring that the

mains switch is in the off position.

Open water tap.

Press the safety lock (back button on the gun handle) to re-

lease the trigger. Fully press the trigger until there is a con-

stant flow of water to clear the air from the machine and wa-

ter supply hose. Release trigger. Press the safety lock (front

button on the gun handle).

Bosch Power Tools F 016 L81 291 | (04.03.2019)

Bosch AdvancedAquatak 150 2200Вт [17/298] Mounting and operation

Содержание

Похожие устройства