ProfiCare PC-PW 3007 FA 8in1 Руководство по эксплуатации онлайн [37/62] 795696

ProfiCare PC-PW 3007 FA 8in1 Руководство по эксплуатации онлайн [37/62] 795696
37
PC-PW3007FA_IM 13.10.17
The signal is generally safe! However, please read our spe-
cial safety instructions!
The method of measurement is referred to as “bioelectric
impedance analysis” (BIA), a factor which is based on the
relationship between body weight and associated body water
percentages as well as on other biological data (age, gender,
body weight).
Use
NOTE:
The buttons are sensor touch buttons. Touch the but-
tons lightly with a nger to execute the function.
The scales are factory set with the units “kg” and “cm”.
To change the settings to “lb” or “st:lb” as well as “ft:in”,
proceed as follows:
1. Turn on the scales by light pressure with the foot onto the
weighing surface.
2. Press the or button repeatedly until the desired
weight unit is displayed. The unit for the height also auto-
matically changes.
Weighing Function
1. Place the scale on a hard, at surface (avoid carpets). An
uneven oor contributes to inaccurate measurements.
2. Stand on the scales with both feet. The appliance
switches on automatically.
3. Distribute your weight equally and wait for the scale to
determine your weight.
4. The digits on the display will ash before your exact
weight will be shown.
In order to extend the battery life, the appliance will
automatically turn off 15 seconds after you have stepped
off the scale.
If there is no weight determination while “0.0” is shown,
the scale will shut off automatically after 15 seconds.
Saving Personal Data
NOTE:
The scale has default values that you can change, as
described below.
Carry out the following steps in sequence and within a
few seconds. Otherwise, the appliance will automati-
cally cancel input mode.
Holding one of the buttons ( / ) pressed for approx.
2 seconds selects fast mode.
1. Press the button . The memory location selected last
ashes on the display (for example P0). Conrm the
setting by pressing or select another memory space
by pressing the / button. Then press to go to the
next setting.
2. The symbol for “male” or “female” will ash. Conrm the
setting by pressing or use the / button to choose
the symbol for your gender. Then press to go to the
next setting.
3. The height setting will ash. Select your height by press-
ing or button. Conrm your entry by pressing .
4. The setting age will ash. Select your age by pressing
or button. Conrm your entry by pressing .
5. The short display “ ” will terminate the entry mode
for this memory location. Then you will see the memory
location, the symbol of the gender and the weight “0.0 kg”
(0.0 lb / 0: 00 st:lb) in the display.
You now have the following options:
Press the button repeatedly to display the settings
again or to change them.
You can set further preset locations. Proceed as de-
scribed above.
You can immediately start measuring.
Measurement and Analysis
Record your personal data in the memory.
NOTE:
The analysis scale will only work correctly when you
are standing on the contact surfaces barefoot and with
slightly moistened foot soles, if possible. Completely
dry foot soles can lead to unsatisfactory results as they
have a conductivity that is too low.
If necessary wipe the contact surfaces to improve
results.
Due to the signicant uctuation of body fat, it is difcult
to attain a standard value. Therefore, to obtain consist-
ent data, always measure at the same time of day.
Amongst other things, our body consists of body
fat, body water, muscle mass and bone weight. The
obtained values may differ due to individual water reten-
tion within these main components. This is normal and
highly dependent on nutrition and lifestyle.
1. Press the button. Use the / button to select the
stored position at which your data is saved. The location
ashes for approx. 3 seconds. Then you will see the
memory location, the symbol of the gender and the weight
“0.0 kg” (0.0 lb / 0: 00 st:lb) in the display.
2. Stand on the contact surfaces (5) of the scales with both
feet.
3. Firstly your weight will ash on the display. The analysis
starts after the display has stopped ashing. You’ll see
a treadmill “ ” in the display during the analysis.
Remain on the scales until the last display ( ) has
appeared.
The following results are displayed one after the other:
1. The weight in the previously selected unit (kg / lb / st:lb)
2. The body fat proportion in % (fat)
3. The proportion of body uid % (TBW)
4. The proportion of muscle mass in % ( )
5. The bone weight in kg ( )

Содержание

Похожие устройства

Скачать