Rondell RDE-1110 [25/48] Side of the menu select the parameter you want to change
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Rondell RDE-1110 [25/48] Side of the menu select the parameter you want to change

Rondell RDE-1110 [25/48] Side of the menu select the parameter you want to change
25
For cappuccino it is better to use rich milk of 3% and above,
for latte 1.5-2.5%. The higher the fat content, the dens-
er and sweeter the froth in general and it lasts longer. Milk
should be as cold as possible, 2-6°C. That is from the refrig-
erator. This affects the frothing. The warmer the initial milk,
the worse it froths.
Preparing the milk system
–
Insert the milk frother (3) into the coffee dispensing unit
(2) (fig. 17) if it has not been installed before, or check
that it is installed correctly (fig. 18).
–
Hold the coffee dispensing unit (2) and press the milk
frother (3) from below upwards on each side until it clicks
(fig. 18). Make sure that the milk frother (3) is securely
held by the locks in the coffee dispensing unit (2).
Notes: The milk frother (3) has two inlets on the left and right
side for installing the tip of the milk tube. A tip is installed in
one hole, a plug in the other. For ease of use, you can install
the tip either on the left or on the right, having previously
removed the plug (fig. 19). After installing the tip, do not
forget to install the plug on the opposite side of the frother.
–
Place one end of the tube on the tip, and put the other end
of the tube with a cutout into a container with milk or con-
nect a thermal container (fig. 20).
If the milk tube is not in use, you can attach its free end to
the tip lock (fig. 21).
If you do not drink coffee drinks with milk at all, you can re-
move the tip with the milk tube from the frother (3) and re-
place it with the plug (supplied with the unit).
Preparing the milk thermal container
The thermal container keeps milk cold longer. Use the ther-
mal container when making coffee drinks with milk and when
making frothed milk.
Unscrew the lid (21), wash all parts of the thermal container
with warm water and neutral detergent and then dry them.
Before using the thermal container, check that the metal
tube is correctly installed in the lid (21), make sure that the
skewed end of the tube is pointing down.
Fill the thermal container tank (20) with cold milk, leaving
at least 2 cm to its edge, close the lid (21). Insert the milk
tube (22) into the lid (21) in such a way that the nozzle with
sealing silicone rings enters the lid outlet until bumping.
Connect the other end of the tube (22) to the inlet of the
milk frother (3).
Adjusting the milk system
For best results, follow the recommendations for choosing
milk. The quality of the frothed milk depends on the qual-
ity and temperature of the milk. It is recommended to use
chilled whole milk.
Before making latte, cappuccino, hot milk or frothed milk,
adjust the milk frother (3) according to your preference.
Open the left door (5) and you will see the milk frother con-
trol knob (15) (fig. 22).
–
Press the «MILK» icon on the main menu, after the coffee
machine has warmed up, the process of making frothed
milk will begin.
If in the process little froth or only hot milk comes out of the
milk frother (3) outlets, slowly turn the control knob (15)
counterclockwise.
If in the process only steam and splashes of milk come out
of the milk frother (3) spout, the froth is not dense, there are
too many milk bubbles, slowly turn the control knob (15)
clockwise.
Slowly turn the control knob (15) to select the optimal ratio.
Drip tray
When the level of liquid in the tray (1) rises to the upper lim-
it, the float level indicator rises, after which it is required to
drain the liquid from the drip tray.
Changing the program settings
You can change the drink making settings according to your
preferences.
–
To change the drink making settings, press the «MENU»
icon on the main menu (fig. 23), and the display will show
the coffee machine settings menu (fig. 24).
–
Press the «SETTINGS» icon, and the display will show the
settings menu for the first drink in the list, «AMERICANO»,
with factory settings (fig. 25), while the icon of the drink
itself and the first setting parameter are highlighted with a
frame of a different color.
–
Select the drink for which you want to change param-
eters, to do this, press the corresponding menu icon
(fig. 26).
– The options for making drinks are located on the right
side of the menu. Select the parameter you want to
change.
–
Set the required value by successively pressing the
parameter icon. Each time you press the icon, the param-
eter will change with a certain setting step.
–
Press the «QUICK START» icon to quickly start making
the drink.
–
To save the settings and return to the main menu, press
the « » icon or wait 45 seconds.
Americano settings: The coffee machine dispenses coffee
first and then hot water to reduce the amount of caffeine.

Содержание

Похожие устройства

Скачать