Panasonic ER131H520 [4/13] Blade maintenance
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Panasonic ER131H520 [4/13] Blade maintenance

Panasonic ER131H520 [4/13] Blade maintenance
76
How to use
<Charging instructions>
1) Set the switch to “0” , and plug
the cord into the clipper body.
(Fig.1)
2) Plug the AC adaptor into an AC
outlet. The charging indicator
lamp will light up. (Fig.2)
3) When charging is completed
unplug the AC adaptor from an
AC outlet. The charging time is 8
hours; 1 full charge will provide
approximately 30 minutes of
continuous operation.
<AC operation>
1) Connect the AC adaptor to the
body in the same way as for
charging, and set the switch to “1”
to use the clipper.
2) If the AC adaptor is connected
while the switch is in the “1”
position, the clipper may not
operate. If this occurs, set the
switch to the “0” position, wait
about 1 minute and then set it
back to the “1” position.
3)
Be sure to set the switch “0” to
when finished using the clipper. If
the switch is left in the “1” position,
the rechargeable battery will
become completely discharged,
shortening the life of the battery.
<3/6mm, 9/12mm comb
attachments>
1) The cutting heights are indicated
on the insides and sides of the
attachments, so be sure to look
for the height indication in order
to mount the attachment correctly
for the desired cutting height.
2)
To mount the comb attachment to
the clipper, place one side of the
hooks of the comb attachment into
the attachment mounting B, then
slide the other side to another
mounting B in the direction
indicated with the arrow. (Fig.3)
3)
To remove the comb attachment
from the clipper, slide one side of
the attachment off the mounting
B
in the direction indicated with the
arrow. (Fig.4)
<Trimming With No
Attachments>
1)
Cut hair by placing the clipper head
directly on the scalp. (Fig.5)
Cutting without an attachment will
trim hair length to 1mm or less.
<Mounting and removal of
the blade>
1) Hold the clipper body with the
“Panasonic” mark facing upward
and push the blade with your
thumb in the direction indicated
by the arrow. When doing this,
catch the blade in your other
hand. Be sure the switch is set to
“0” before attempting to remove
the blade. (Fig.6)
2)
To remount the blade, fit the
mounting hook into the blade
mounting on the clipper body and
push in until it “clicks”. (Fig.7)
Life of the blade and battery
<Blade life>
1) Although the blade life will vary in
accordance with the frequency
and conditions of use, when used
for five haircuts (each lasting 12
minutes) a day, it should normally
be possible to use the blade for
approximately three months.
However, in order to maintain the
cutting performance of the blade,
it is important to apply the oil
before and after each use.
2) If the cutting performance of the
blade deteriorates and cannot be
restored by cleaning or applying
the oil, it indicates that the blade
has exceeded its useful life, and
that it is time to replace it.
<Battery life>
Although the battery life will vary in
accordance with the frequency and
conditions of use, when charged
every day, it should normally be
possible to use the battery for
approximately 1 year. If the
rechargeable battery is not charged
for longer than 6 months, it will self
discharge, resulting in a shortening
of its life. Therefore, even if the
clipper is not being used, be sure to
recharge the battery at least once
every 6 months. If the clipper can be
operated for only about 10 minutes
after it has been correctly recharged
for 8 hours, it indicates that the
battery has exceeded its useful life
and that it is time to replace it.
Blade Maintenance
<Always clean the blade
after each use>
1) Use the cleaning brush to brush
off the cut hairs from the clipper
body and from around the blade.
(Fig.8)
2) Remove the blade and brush off
the cut hairs from the blade edge.
3) Brush the cut hairs out from
between the fixed blade and the
moving blade. Press down on the
lever for cleaning in order to raise
the moving blade, and brush the
cut hairs out from between the
blades. (Fig.9)
4) Apply a few drops of the oil to the
points indicated by the arrows.
(Fig.10)
5) Remount the blade on the clipper
body.
0408ER131取説(欧州)06.02.2318:23 ページ6

Содержание

Похожие устройства

Скачать