Makita LXT BL 18 В DUX18Z [13/116] Electronic torque control function

Makita LXT BL 18 В DUX18Z [13/116] Electronic torque control function
13 ENGLISH
Overheat protection for tool or battery
Whenthetoolorbatterycartridgeisoverheated,thetoolstops
automaticallyandtheindicatorlamplightsupinred.Letthe
tooland/orbatterycooldownbeforeturningthetoolonagain.
Overdischarge protection
Whenthebatterycapacitybecomeslow,thetoolstops
automatically.Theindicatorlampstartsblinkinginred.
If the tool does not operate even when the switches are oper-
ated,removethebatterycartridgefromthetoolandchargeit.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
►Fig.7: 1. Indicator lamps 2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75%to100%
50%to75%
25%to50%
0%to25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydi󰀨erslightly
fromtheactualcapacity.
NOTE:Therst(farleft)indicatorlampwillblinkwhen
thebatteryprotectionsystemworks.
Main power switch
WARNING: Always turn o󰀨 the main power
switch when not in use.
Pressthemainpowerbuttontoturnonthetool.Toturno󰀨thetool,
pressandholdthemainpowerbuttonuntiltheindicatorlampsgoo󰀨.
►Fig.8: 1. Indicator lamps 2.Mainpowerbutton
NOTE:Theindicatorlampbrinksiftheswitchtrigger
ispulledunderunoperatableconditions.Thelamp
blinksifyouturnonthemainpowerswitchwhilehold-
ingdownthelock-o󰀨leverandtheswitchtrigger.
NOTE:
Thistoolemploystheautopower-o󰀨function.To
avoid unintentional start up, the main power switch will auto-
maticallyshutdownwhentheswitchtriggerisnotpulledfor
a certain period after the main power switch is turned on.
Switch action
WARNING: For your safety, this tool is
equipped with lock-o󰀨 lever which prevents the
tool from unintended starting. NEVER use the tool
if it runs when you simply pull the switch trigger
without pressing the lock-o󰀨 lever. Return the
tool to our authorized service center for proper
repairs BEFORE further usage.
WARNING: NEVER tape down or defeat pur-
pose and function of lock-o󰀨 lever.
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION: Never put your nger on the main
power button and switch trigger when carrying
the tool.Thetoolmaystartunintentionallyandcause
injury.
NOTICE: Do not pull the switch trigger hard with-
out pressing the lock-o󰀨 lever. This can cause
switch breakage.
Topreventtheswitchtriggerfrombeingaccidentally
pulled,alock-o󰀨leverisprovided.
►Fig.9: 1.Lock-o󰀨lever2. Switch trigger
To start the tool, turn on the main power switch and
graspthehandle(thelock-o󰀨leverisreleasedbythe
grasp) and then pull the switch trigger. Tool speed is
increasedbyincreasingthepressureontheswitch
trigger. To stop the tool, release the switch trigger.
Speed adjusting
Youcanselectthetoolspeedbytappingthemain
powerbutton.Eachtimeyoutapthemainpowerbutton,
the level of speed will change.
►Fig.10: 1. Indicator lamps 2.Mainpowerbutton
Indicator lamps Mode
High
Low
Electronic torque control function
Thetoolelectronicallydetectsasuddendropinthe
rotationspeedwhichmaycauseakickback.Inthis
situation,thetoolautomaticallystopstopreventfurther
rotation of cutting tool. To restart the tool, release the
switch trigger. Clear the cause of sudden drop in the
rotation speed and then turn the tool on.
NOTE: This function is not a preventive measure for
kickbacks.

Содержание

Похожие устройства

Скачать