Home
Главная
Makita
Ленточные
LXT DBS180Z
Инструкция Страница: 8

Makita LXT DBS180Z [8/64] Assembly

8 ENGLISH

Adjusting arm inclination

The arm can be pivoted and xed at any desired angle

within the range "A" (-5° to 90°) in the gure. Adjust the

angle to make a comfortable working position.

Loosen the lock lever by raising it. Pivot the arm to the desired

position, and secure the lock lever to x the arm rmly.

► Fig.3: 1. Lock lever 2. Arm

Replacing arm

6 mm (1/4″) and 13 mm (1/2″) width belts can be

installed with the optional arms that are designed for

the corresponding belt widths. Loosen the screw that

secures the arm and replace the standard-equipped

arm with the optional arm, then tighten the screw rmly.

► Fig.4: 1. Screw 2. Arm

Switch action

WARNING: For your safety, this tool is

equipped with the lock-o󰀨 switch which prevents

the tool from unintended starting. NEVER use

the tool if it runs when you simply pull the switch

trigger without releasing the lock-o󰀨 switch.

Return the tool to our authorized service center

for proper repairs BEFORE further usage.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released. Operating a tool

with a switch that does not actuate properly can lead

to loss of control and serious personal injury.

NOTICE: Do not pull the switch trigger hard with-

out releasing the lock-o󰀨 switch. This can cause

switch breakage.

NOTICE: The lock-o󰀨 switch cannot be released

while the arm is being pivoted beyond 90°.

To prevent the switch trigger from being accidentally

pulled, a lock-o󰀨 switch is provided. Depress the switch

lever ( ) from the A side to unlock the switch trigger,

and ( ) from the B side to lock in.

► Fig.5: 1. Lock-o󰀨 switch

To start the tool, pull the switch trigger. Release the

switch trigger to stop.

For continuous operation, pull the switch trigger and

then push in the lock button. To stop the tool from the

locked switch position, pull the switch trigger fully, and

then release it.

► Fig.6: 1. Lock-on button 2. Switch trigger

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

The lighting direction can be adjusted at three levels

through an angle of 60°. Pull the switch trigger to turn on

the lamp. To turn o󰀨, release it. The lamp goes out approxi-

mately 10 seconds after releasing the switch trigger.

► Fig.7: 1. Lamp

NOTE:

When the tool is overheated, the light ashes for one

minute. In this case, cool down the tool before operating again.

NOTE: Use a dry cloth to wipe the dirt o󰀨 the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Speed adjusting dial

The belt speed can be adjusted between 600 m and

1,700 m per minute (1,970 - 5,600 ft/min) by turning the

speed adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the

direction of number 5; lower speed is obtained when it

is turned in the direction of number 1. Select the proper

speed for the workpiece to be sanded.

CAUTION:

The speed adjusting dial can only be

turned between the numbers indicated on the dial. Do

not apply an excessive force to turn the dial outside

that range, or the speed adjustment may not function.

► Fig.8: 1. Speed adjusting dial

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o󰀨 and the battery cartridge is removed

before carrying out any work on the tool.

Removing and installing abrasive belt

Pull the cam lever back to release the tension in the

belt, and remove the belt.

To install the belt, place one side of the belt over the

rear pulley in rst, hook the other side over the front pul-

ley, and then set the cam lever to the original position.

► Fig.9: 1. Cam lever 2. Abrasive belt 3. Rear pulley

4. Front pulley

Adjusting belt tracking

Make sure that the belt is aligned with the arm properly

on a trial run at low speed.

Use the thumb screw to center the belt tracking. Turn

the screw clockwise to incline the arm to the right when

looking down at the tool with its arm pointed forward,

and in counterclockwise to the left.

► Fig.10: 1. Arm 2. Thumb screw

Installing side grip

CAUTION: Securely tighten the thumb screw

before operation.

CAUTION:

Avoid exerting a strong external force

on the side grip, otherwise the grip base becomes

loosely attached and the tool may fall o󰀨 causing

damage or personal injury in the following conditions:

•

Apply a full impact on the side grip during operation

• Handle the tool carelessly only with one hand on

the side grip

•

Carry the tool only with one hand on the side grip

Makita LXT DBS180Z [8/64] Assembly

Содержание

Похожие устройства