Home
Главная
Stiga
COMBI 53 SQ H
Инструкция по эксплуатации Страница: 14

Stiga COMBI 53 SQ H — руководство по эксплуатации: подготовка и запуск двигателя [14/228]

Stiga COMBI 53 S4Q B [14/228] Standards of use

BEFORE EVERY USE

Before every use, perform the following checking

procedures in order to assure a regular opera-

tion.

Check oil level

See the specific chapter (see 8.1) for the oil to be

used.

a) Place engine level.

b) Clean around oil fill.

c) Unscrew the cap (1), clean the end of the dip-

stick (2) and insert it, as illustrated, without

screwing it down.

d) Remove the cap with the dipstick and check

the oil level that must be between the «MIN»

and «MAX» marks.

e) If oil is required, add oil of the same kind up

to the «MAX» mark, being careful not to spill

any outside the oil fill.

f) Fully tighten the fillercap (1) and wipe off any

spilled oil.

Check air cleaner

The efficacy of the air cleaner is crucial for the

good performance of the engine; never start the

engine if the filter element is missing, broken or

insufficiently saturated with oil.

a) Clean around the filter cover (1).

b) Remove the cover (1) by releasing the tabs

(2).

c) Check the condition of the filtering element

(3). It must be intact, clean and in perfect

working order; if not, either carry out mainte-

nance or replace it (see 6.5).

d) Put the cover (1) back.

Adding fuel

Do not drip petrol onto the

plastic parts of the motor or the machine to

prevent damaging them and remove all traces

of spilt petrol immediately. The warranty does

not cover damage to plastic parts caused by

petrol.

See “Technical Data” chapter (see 8.1) for the

fuel characteristics.

IMPORTANT

5.1.3

5.1.2

5.1.1

5.1

5. STANDARDS OF USE

Add fuel only when the engine is cold.

a) Place the lawnmower level.

b) Clean around the fillercap (1).

c) Remove the fillercap (1).

d) Using a clean funnel (2), add fuel until it

reaches the internal lip (3) of the filler, taking

care not to spill any fuel.

e) Tighten the fillercap (1) back and clean any

spilled fuel.

Spark plug cap

Firmly connect the cable cap (1) to the spark

plug (2), making sure that there are no traces of

debris or dirt inside the cap or on the spark plug

terminal.

STARTING THE ENGINE (cold)

The engine must only be started when all the

accessory devices are disconnected (if fitted on

the machine) and when the gear (where fitted) is

in neutral.

– Move the throttle (1) to «CHOKE».

– Set the machine controls as indicated in the

machine’s Instructions Manual.

• Manual starting

a) Hold the starter rope grip (3) and pull it slow-

ly until you feel some resistance, then tug the

starter rope hard.

b) When the engine starts, let go of the rope.

If the engine fails to start

immediately, repeat the above steps.

• Electric starting (if provided)

a) Turn the starter key (4) as described in the

machine’s instruction manual.

After a few seconds, slowly move the throttle (1)

from «CHOKE» to either «FAST» or «SLOW».

If the engine starts but does

not keep running, repeat the above steps with

the throttle on «FAST».

NOTE

5.2

5.1.4

Содержание

Похожие устройства

4 I EN I 5 STANDARDS OF USE I 5 1 BEFORE EVERY USE Before every use perform the following checking procedures in order to assure a regular opera tion Add fuel only when the engine is cold a Place the lawnmower level b Clean around the fillercap 1 c Remove the fillercap 1 d Using a clean funnel 2 add fuel until it reaches the internal lip 3 of the filler taking care not to spill any fuel e Tighten the fillercap 1 back and clean any spilled fuel 5 1 1 Check oil level See the specific chapter see 8 1 for the oil to be used a Place engine level b Clean around oil fill c Unscrew the cap 1 clean the end of the dip stick 2 and insert it as illustrated without screwing it down d Remove the cap with the dipstick and check the oil level that must be between the MIN and MAX marks e If oil is required add oil of the same kind up to the MAX mark being careful not to spill any outside the oil fill f Fully tighten the fillercap 1 and wipe off any spilled oil 5 1 4 Spark plug cap Firmly connect the cable cap 1 to the spark plug 2 making sure that there are no traces of debris or dirt inside the cap or on the spark plug terminal I 5 2 I STARTING THE ENGINE cold The engine must only be started when all the accessory devices are disconnected if fitted on the machine and when the gear where fitted is in neutral Move the throttle 1 to CHOKE Set the machine controls as indicated in the machine s Instructions Manual 5 1 2 Check air cleaner The efficacy of the air cleaner is crucial for the good performance of the engine never start the engine if the filter element is missing broken or insufficiently saturated with oil a Clean around the filter cover 1 b Remove the cover 1 by releasing the tabs 2 c Check the condition of the filtering element 3 It must be intact clean and in perfect working order if not either carry out mainte nance or replace it see 6 5 d Put the cover 1 back 5 1 3 Adding fuel IMPORTANT D0 not drip petrol onto the plastic parts of the motor or the machine to prevent damaging them and remove all traces of spilt petrol immediately The warranty does not cover damage to plastic parts caused by petrol Manual starting a Hold the starter rope grip 3 and pull it slow ly until you feel some resistance then tug the starter rope hard b When the engine starts let go of the rope I to start Electric starting if provided a Turn the starter key 4 as described in the machine s instruction manual After a few seconds slowly move the throttle 1 from CHOKE to either FAST or SLOW I See Technical Data chapter see 8 1 for the fuel characteristics NOTE if ff e fans engine immediately repeat the above steps NOTE if fiie engine starts but does not keep running repeat the above steps with the throttle on FAST

Узнайте, как правильно подготовить и запустить двигатель. Следуйте инструкциям по проверке уровня масла, добавлению топлива и запуску устройства для безопасной работы.