Home
Главная
Black & Decker
Шлифмашина
KG 915 К
Инструкция по эксплуатации Страница: 7

Black & Decker KG 915 К [7/96] English

ENGLISH

 Position the cord clear of the spinning ac-

cessory. If you lose control, the cord may be

cut or snagged and your hand or arm may be

pulled into the spinning accessory.

 Never lay the power tool down until the ac-

cessory has come to a complete stop. The

spinning accessory may grab the surface and

pull the power tool out of your control.

 Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

 Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the

housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

 Do not operate the power tool near ﬂ am-

mable materials. Sparks could ignite these

materials.

 Do not use accessories that require liquid

coolants.

Using water or other liquid coolants may result

in electrocution or shock.

Note: The above warning does not apply for power

tools speciﬁ cally designed for use with a liquid

system.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or any

other accessory.

Pinching or snagging causes rapid stalling of

the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of

the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction of

the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

 Maintain a ﬁ rm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control

over kickback or torque reaction during

start-up. The operator can control torque reac-

tions or kickback forces, if proper precautions

are taken.

 Never place your hand near the rotating ac-

cessory.

Accessory may kickback over your hand.

 Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snag-

ging.

 Use special care when working corners,

sharp edges etc. Avoid bouncing and snag-

ging the accessory.

Corners, sharp edges or bouncing have a ten-

dency to snag the rotating accessory and cause

loss of control or kickback.

 Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades

create frequent kickback and loss of control.

Additional safety instructions for grinding

and cutting-off operations

Safety warnings speciﬁ c for grinding and abra-

sive cutting-off operations

 Use only wheel types that are recommended

for your power tool and the speciﬁ c guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot

be adequately guarded and are unsafe.

 The guard must be securely attached to the

power tool and positioned for maximum

safety, so the least amount of wheel is ex-

posed towards the operator. The guard helps

to protect operator from broken wheel fragments

and accidental contact with wheel.

 Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them

to shatter.

 Always use undamaged wheel ﬂ anges that

are of correct size and shape for your se-

lected wheel. Proper wheel ﬂ anges support

the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be

different from grinding wheel ﬂ anges.

 Do not use worn down wheels from larger

power tools. Wheel intended for larger power

tool is not suitable for the higher speed of

a smaller tool and may burst.

Black & Decker KG 915 К [7/96] English

Содержание

Похожие устройства