Suunto HelO2 [17/64] Wireless transmission
Omitted decompression
The Error mode results from omitted decompression, i.e. when you stay above the ceiling
for more than three minutes. During this three-minute period the Er warning is shown and
the audible alarm beeps. After this, the dive computer will enter a permanent Error mode.
The instrument will continue to function normally if you descend below the ceiling within
this three-minute period.
Once in the permanent Error mode, only the Er warning is shown in the center window.
The dive computer will not show times for ascent or stops. However, all the other displays
will function as before to provide information for ascent.You should immediately follow
through the decompression schedule in your backup plan.
After surfacing, you should not dive for a minimum of 48 hours. During the permanent
Error mode, the Er text will be displayed in the center window and the planning mode will
be disabled.
5.8. Wireless transmission
The HelO
2
can be used together with a wireless cylinder pressure transmitter that easily
attaches to the high-pressure port of the regulator. By using the transmitter, you can be-
nefit from receiving cylinder pressure data direct to your wrist.
In order to use the transmitter, the wireless integration needs to be enabled in your Suunto
HelO
2
settings. To enable or disable the wireless integration refer to Section 5.9.7. Setting
the tank pressure.
5.8.1. Installing the wireless transmitter
When purchasing the Suunto HelO
2
, we strongly recommend that you have your Suunto
representative attach the transmitter to the first stage of your regulator.
However, if you decide to attach it yourself, do the following:
1.
Remove the high pressure (HP) port plug on the first stage of your regulator using an
appropriate tool.
2.
Thread the high pressure transmitter of the Suunto into the HP port of your regulator
with your fingers. DO NOT OVERTIGHTEN! Maximum torque is 6 Nm/4.4 lbsft or 53
lbsin. The seal is based on a static O-ring, not force!
3.
Attach the regulator to the scuba cylinder and slowly open the valve. Check for leaks
by submerging the regulator first stage in water. If leaks are detected, check the
condition of the O-ring and sealing surfaces.
5.8.2. Pairing and code selection
In order to receive wireless data, the transmitter and the Suunto HelO
2
need to be paired.
During the pairing procedure, the transmitter and dive computer select a common trans-
mission code.
The transmitter is activated when the pressure exceeds 15bar/218 psi and it then starts
sending pressure data together with a code number. During the pairing procedure, the
Suunto HelO
2
stores the code number and starts displaying pressure values that are re-
ceived with that code. This coding procedure inhibits data mix-up from other divers also
using a Suunto HelO
2
transmitter.
When there is no stored code, the Suunto HelO
2
displays “cd:--” and receives data with
lowered sensitivity from a very short distance only. By taking the Suunto HelO
2
close to
the transmitter, it will store the received code and start receiving with full sensitivity and
display data received with this code only. The code is stored until you reset it manually.
To pair the transmitter and the Suunto HelO
2
dive computer:
1.
Make sure that the transmitter is properly attached to the regulator’s HP port and that
the regulator is properly attached to the cylinder.
17
Содержание
- Suunto helo2 user s guide 1
- User s guide 1
- Table of contents 3
- Using helo2 with dive manager and dive planner 5
- Welcome to the world of suunto diving instruments 5
- Warnings cautions and notes 6
- Button symbols and functions 9
- Navigating in the menus 9
- Suunto helo2 at a glance 9
- Getting started with your suunto helo2 11
- Setting the date 11
- Setting the time 11
- Setting the units 11
- Time mode settings 11
- Ac water contacts 12
- Setting the backlight 12
- Setting the tones 12
- Before diving 13
- Planning your dives 13
- The suunto technical rgbm 13
- Dive computer limitations 14
- Emergency ascents 14
- Mixed gas diving 14
- Audible and visual alarms 15
- Error conditions 16
- Installing the wireless transmitter 17
- Pairing and code selection 17
- Wireless transmission 17
- Transmitting data 18
- Mixed gas dive mode settings 19
- Setting the gases 19
- Setting the depth alarm 20
- Setting the dive time alarm 20
- Setting the personal altitude adjustments 20
- Setting the hp code 21
- Setting the sample rate 21
- Setting the tank pressure 21
- Setting the tank pressure alarm 21
- Accessing dive mode 22
- Activation and pre checks 22
- Dive mode activation 22
- Setting the units 22
- Battery power indication 23
- Diving at altitude 23
- Personal adjustments 24
- Mandatory safety stops 25
- Recommended safety stops 25
- Safety stops 25
- Deep stops 26
- Basic dive data 27
- Diving 27
- Diving related information 27
- Ascent rate indicator 28
- Bookmark 28
- Decompression dives 28
- Safety stops 28
- Ceiling ceiling zone floor and decompression range 29
- Display above the ceiling 30
- Display above the floor 30
- Display at the ceiling zone 30
- Display below the floor 30
- Before diving in mixed gas mode 31
- Default gas mix settings 31
- Diving in mixed gas mode 31
- Oxygen and helium displays 31
- Gas change and multiple breathing gas mixes 32
- Oxygen limit fraction olf 32
- Diving in gauge mode 33
- After diving 34
- Dive numbering 34
- Surface interval 34
- Dive planning mode plannodec 35
- Flying after diving 35
- Plan mode 35
- Repetitive dive planning 35
- Dive numbering shown during dive planning 36
- Memory mode 36
- Dive logbook memlogbook 37
- Dive history 38
- Suunto dive planner sdp 38
- Suunto dive manager sdm 39
- Www suuntosports com and suunto diving world at www suunto com diving 39
- Care and maintenance of my suunto diving computer 41
- Battery kit 43
- Battery replacement 43
- Replacing the battery 43
- Required tools 43
- Battery 44
- Battery compartment lid with buzzer 44
- Battery retainer 44
- O ring 44
- Securing ring 44
- Wireless transmitter battery replacement 44
- Replacing the transmitter battery 45
- Required tools 45
- Transmitter battery kit 45
- Technical data 47
- Technical specifications 47
- Diver safety and suunto technical rgbm model 49
- Suunto technical rgbm decompression model 49
- Altitude diving 50
- Oxygen exposure 50
- Copyright 51
- Intellectual property 51
- Patent notice 51
- Trademark 51
- Disclaimers 52
- User s responsibility 52
- Suunto limited warranty for suunto diving com puters and suunto diving computer accessories 53
- Suunto limited warranty for suunto diving computers and suunto diving computer accessories 53
- Disposal of the device 56
- Glossary 57
- Copyright 59
- Customer service contacts 59
- Two year warranty 61
Похожие устройства
- D-Link DSL-500T Инструкция по эксплуатации
- Viking VH 660 Инструкция по эксплуатации
- JVC TH-S3 Инструкция по эксплуатации
- Elikor Europa 60 черный (290) пп Инструкция по эксплуатации
- Zelmer 886.5 BE Инструкция по эксплуатации
- Suunto Gekko Инструкция по эксплуатации
- Yamaha PSR-1500 Инструкция по эксплуатации
- D-Link DSL-200 (v.B1) Инструкция по эксплуатации
- Sungarden T250 BR 5.0 Инструкция по эксплуатации
- JVC TH-M45 Инструкция по эксплуатации
- Elikor Europa 50 черный (290) пп Инструкция по эксплуатации
- JVC TH-A9R Инструкция по эксплуатации
- Suunto D9tx Инструкция по эксплуатации
- Dekok UKA-1223 Инструкция по эксплуатации
- Yamaha PSR-175 Инструкция по эксплуатации
- Texas Lilli 532 B Инструкция по эксплуатации
- D-Link DSL-300T Инструкция по эксплуатации
- JVC TH-A85 Инструкция по эксплуатации
- Suunto D9 Инструкция по эксплуатации
- Yamaha PSR-295 Инструкция по эксплуатации