Krona IEC 2634T IX Инструкция по эксплуатации онлайн [15/44] 133653

- 15 -

USE

Use the touch control system in the corresponding posi-

tion relative to the individual cooking needs. Keep in

mind that the higher the number, the more heat that it is

produced.

Operation (fig.4-5)

A = ON/OFF button

B = Lock button

C = + button

D = - button

E = ON/OFF indicator light lock button

F = Cooking zone selector button

G = Double cooking zone ON/OFF indicator light

I = Rapid heating function (Heat up) active

L = Double zone selector button

P = Timer buttons (+ / -)

Q = Cooking zone display

R = Timer Display

- The appliance can be switched on by selecting start-up

sensor A. A zero will appear on all displays for 10 sec-

onds. If no command is made within 10 seconds, the hob

will switch off again.

- A hotplate can be switched on by selecting the “+” or “-

” sensor within 10 seconds. If sensor D is used the

display will show selection 9, while if sensor C is used,

the display will show selection 1.

- Once this step is complete the user may make tem-

perature adjustments using the “+” or “-” buttons.

- The hotplate can be switched off by selecting “0” using

sensor D; after 3 seconds the cooking zone will switch

off.

A hotplate can also be switched off by selecting the “+”

or “-” sensors simultaneously.

- The hob can be switched off by selecting the main

start-up sensor A. If all the hotplates are set to “0” the

hob switches off after 10 seconds.

- If the hob is fitted with extendable hotplates, the sec-

ond zone may be switched on after the user has ensured

that:

- the LED corresponding to lock button B is switched off

(if it is not, deactivate it).

- Press button A to switch on the hob.

- Select the desired hotplate and adjust the power level

using the “+” and “-” buttons.

- Once the power has been adjusted, select button L to

activate the double zone.

- To deactivate the double zone, simply press button L.

- If an object has been placed on top of the control

panel, the hob will automatically revert to OFF mode.

When a hotplate is in the OFF mode and the temperature

of the glass surface is greater than approximately 50°,

there will be a light signal “H” on the corresponding

cooking zone display.

- Function B locks hob operation the moment it is se-

lected. E.g.: if the function is activated when two zones

of the hob are switched on, the programme remains

locked at that level, even if the user attempts to switch

on another zone. The same thing happens if the appli-

ance is switched off and the lock function is activated:

the user will not be able to switch the hob on.

To activate or deactivate it, hold a finger in front of

sensor B for approximately two seconds. The function is

active when indicator light E is illuminated.

Even when the lock button is activated, button A will

continue to work.

Heat up (Rapid heating)

Select the hotplate by pressing the + button until setting

9 is displayed; if the button is pressed again a decimal

point will appear on the display (next to the digit 9) for 5

seconds. This means the “Heat up” function is active.

The desired power level (between 1 and 8) should be

selected within 5 seconds.

If power level 9 is selected, the function is disabled.

To deactivate the Heat up function, simply select the +

button and hold it down until setting 9 is reached and the

decimal point disappears from the display.

When the “Heat up” function is active, the previously

selected temperature level may be increased by press-

ing the (+) button.

Once the cooking zone has reached the selected tem-

perature, the “Heat up” function is automatically deacti-

vated and the hob emits a BEEP. The cooking zone will

operate in a constant manner, at the set power level.

Timer (fig. 5)

Depending on the model of the hob, it may be equipped

with a TIMER function.

This function can be used to set an amount of time

(between 00 and 99 minutes) after which the selected

cooking zone will switch off automatically.

Operation:

- Select the + or - button corresponding to function P; 00

will appear on the timer display.

- Use the “+” and “-” buttons to set the desired timer

period.

- If the + button is pressed for more than 2 seconds, the

desired time values can be reached more quickly.

- Select a cooking zone and set the desired temperature

level (between 1 and 9).

- Once the programmed time has elapsed, display P will

emit a sound signal and will begin to flash.

This signal can be deactivated by touching the + and -

buttons on timer display P.

- If you wish to stop the TIMER function before the set

time has elapsed, press the + and - buttons simulta-

neously.

THE MANUFACTURER DECLINES ALL RESPONSIBIL-

ITY FOR EVENTUAL DAMAGES CAUSED BY BREACH-

ING THE ABOVE WARNINGS.

Krona IEC 2634T IX Инструкция по эксплуатации онлайн [15/44] 133653

Содержание

Похожие устройства